A 10 kN post is applied to the fixed-supported steel post as shown in the figure.The post has a constant diameter of 100 m. The yield strength of the materialused is 250 MPa. Compute the following:10KN0.5m+21.5m+ZFigure 2+XA. The principal stresses acting at point A.B. The Von-mises equivalent stress at point A.+XC. The factor of safety with respect to yielding at point A based on MaximumDistortion Energy Theory.

GivenFZ=10 kNNote - post diamter 100m too much large as compare to its length 1.5m. It must be 100mm…

A 10 kN post is applied to the fixed-supported steel post as shown in the fig The post has a constant diameter of 100 m. The yield strength of the materi used is 250 MPa. Compute the following: 10kN 0.5m +X

A 10 kN post is applied to the fixed-supported steel post as shown in the fig The post has a constant diameter of 100 m. The yield strength of the materi used is 250 MPa. Compute the following: 10kN 0.5m +X

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A rectangular steel block is 4inches long in the x direction, 2inches long in the y direction, and…

Q: A material having a shear modulus G, is deformed under a pure shear stress as shown in the following…

A: Given, a= 2mm, b= 100 mm and G = 25 GPa

Q: A mechanism used in printing machinery consists of a helical spring which is having a wire diameter…

Q: 1. A Rectangular bar as shown in Figure 1 is made of structural steel and subjected to a tension of…

A: It is asked to find the Von-Mises stress and directional displacement of the model given below.…

Q: A solid circular bar is surrounded by a layer of copper rigidly attached to it, the assembly is…

Q: A stepped bar is subjected to an axial tensile force of 40000 lb. Compute the increase in stress due…

Q: wo plates 16 mm thick are joined by a double riveted lap joint. The pitch each row of rivets is 90…

Q: 3. A tubular aluminium bar (G = 30 GPa) of square cross-section as shown below, with outer…

A: To Find : The minimum required wall thickness Given : The allowable shear stress is The torque is…

Q: We are given the vertical cantilever of Fig. 1, which is subjected to a horizontal distributed load…

Q: A material having a shear modulus G, is deformed under a pure shear stress as shown in the following…

A: Shear stress : When an external force acts on an object, It undergoes deformation. If the direction…

Q: A steel rod 2.5m long is secured between two walls. If the load on the rod is zero at 20°C,…

Q: A horizontal steel rod is secured on a wall as shown. If the rod is initially stress-free, compute…

Q: Find the final length of the bar of an aluminum alloy with a modulus of elasticity of 68.8 GPa,…

Q: A closed thin walled cylindrical vessel has a diameter D of 890 mm, a wall thickness t of 1.5 mm and…

Q: FIND THE AREA USING SODERBERG PRINCIPLE

A: Given data; P1=20 kNP2=100 kNσyt=240 MPaσe=160MPaF.O.S=2

Q: and also find the fillet radius(r) Take theoretical stress concentration factor as 2.5. Also find…

Q: A long, flat steel bar 260mm wide and 35mm thick has a circular hole 50mm in diameter, centrally…

Q: Example 1.6 Around bar as shown in Fig-1- is subjected to an axial tensile load Of 100KN . what must…

Q: A circular bar of magnesium alloy is (700+Reg/10) mm long. The stress-strain diagram for the…

A: Given data: Length of magnesium alloy, L = (700+Reg/10) mm. The value for Reg, Reg = 66.…

Q: Determine the total deformation of the steel rod shown in figure (1) under the given loads. Take the…

Q: You are given a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m). The…

Q: An aluminum pipe is filled in concrete is subjected to a pure compressive force as shown in the…

Q: A horizontal steel rod is secured on a wall as shown. If the rod is initially stress-free, compute…

A: Stress produces in the material due to changes in temperature is known as thermal stress. Condition…

Q: A steel circular tube is subjected to torsion by torques T applied at the ends as shown below. The…

A: This problem is related to the torsion of the shaft. torsion, when the twisting moment is applied to…

Q: et's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a…

Q: Calculate the compression resistance in kN of the cross-section of a stocky universal beam (UB)…

Q: A mechanism used in printing machinery consists of a helical spring which is having a wire diameter…

Q: In constructing a large mobile, Jude hangs an aluminum sphere of mass 6.0kg from a vertical steel…

Q: A reinforced concrete column is constructed of 12 1-in-diameter steel rods. Calculate the force…

Q: A mechanism used in printing machinery consists of a helical spring which is having a wire diameter…

A: Data given- d = 5 mm Do = 54 mm n = 16 Permissible shear stress = 335 N/mm2 G = 82 kN/mm2

Q: An ASTM A36 structural steel beam 4.00 m long is placed between two rigid supports when the…

A: The magnitude of the stress-induced in the object due to the rise in the temperature of the object…

Q: An idealized model of a thin-walled convertible car body cross-section is shown in figure Q16. The…

Q: Acolumn of rainforced concrete has steel reinforcing rods running through its entire length and…

Q: The cross - sectional area of an aluminum bar is 170 mm?. It carries an axial load at the positions…

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

A 10 kN post is applied to the fixed-supported steel post as shown in the figure.
The post has a constant diameter of 100 m. The yield strength of the material
used is 250 MPa. Compute the following:
10KN
0.5m
+2
1.5m
+Z
Figure 2
+X
A. The principal stresses acting at point A.
B. The Von-mises equivalent stress at point A.
+X
C. The factor of safety with respect to yielding at point A based on Maximum
Distortion Energy Theory.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

100 N R 19 PO A S 50 KN Z 0.9m Im W 0.2m Figure 1: Representation of the Lamp Post with Bracket 0.85m Note that: Height (h)=6 Thickness (t)=20 Calculate the ff: a. Consider that you want to evaluate a very short segment of length AL that runs along the middle of bar SW. What is the deformation along x, y and z in terms of AL? Take the case of linear-elastic behavior. G = 75 gigapascals E is 185 gigapascals Figure 2: Detailing of the Pin Support at W
A solid circular rod 200 mm long and 20 mm in diameter has an axial force of P. are exposed. P force and elongation of the rod when this force is applied is below the elasticity of the material, taking as the values given opposite your names in the table presented Calculate the modulus E and the shear modulus G. Take the Poisson's ratio () 0.3. P (N) δ(mm) :500 1,6
A steel rod with a cross-sectional area of 0.25in .^ 2 is stretched between two fixed points. The tensile load at 0.7 deg * Fis * 1200 lb. What will be the stress at 0 deg * F ? At what temperature will the stress be zero? Assume alpha = 6.5 * 10 ^ - 6 in ./(in*^ F) and E = 29 * 10 ^ 4 psi.
4. A steel rod of length L and uniform cross sectional area A is secured between two walls, as shown. Use L=1.7 m, E = 200 GPa, a = 11.9 × 10-6 /°C and AT = 70 °C. Calculate the stress for a temperature increase of AT for: a) The walls are fixed. b) The walls move apart a distance 0.4 mm. (20 pts)
A cantilever beam of circular cross-section is made of alloy steel is subjected to a fluctuating load that varies from -F to 2F. Determine the minimum ultimate strength of the beam material which can withstand the fluctuating loads. The variable forces on the beam induce corresponding fluctuating stresses between + 48 N/mm2 to -24 N/mm?. Assume the following values. Yield strength = 0.55 ultimate strength, endurance stress = 0.45 ultimate strength. Take a factor of safety = 2. Use Soderberg relation in your design i) Calculate mean and alternating stress ii) Calculate endurance strength **Note: Please upload your handwritten working/solution to the link provided. Mean Stress in N/mm^2 ... Variable Stress in N/mm^2 ... Endurance Strength in N/mm^2 .. Ultimate Strength in N/mm^2..
A solid steel bar 250 mm long is 10 mm square over part of its length, the remainder being circular with a diameter of 25 mm. A gradually applied tensile load P kN induces maximum stress in the bar of 200 MPa. The total strain energy in the bar when this stress of 200 MPa is acting is 1,3 Joule. Take E = 200 GPa Calculate : The load The length of the square portion of the bar The load that falls from a height of 8 mm and induces 1,3 Joules in the bar
Don't copy from any source and don't give handwritten solution
A round cast iron column 5m long and 299mm ...
A circular rod of diameter 8 mm and 300 mm long is subjected to a tensile force 20 kN. Take E = 200KN /mm? . Find stress, strain and elongation of the bar due to applied load.
materials resistance
Solve following the problems below and show your complete, systematic and neat solution. Upload your solution with one PDF file. 1. For the beam shown, a. determine the maximum flexural stresses in compression ant tension. b. determine the flexural stress of the fiber located at 3m from the left support and 50 mm above the bottom 18 kN/m 300 mm 6 kN/m 20 mm 27 kNm 22 2m 2m 3 m +m 15 mm - - 50 mm 360 mm 20 mm
A bar is subjected to fluctuating tensile load from 20 kN to 100 kN. The material has yield strength of 240 MPa and endurance limit in reversed bending is 160 MPa. According to the Soderberg principle, the area of cross-section in mm2 of the bar for a factor of safety of 2 is