The hollow circular pipe is subjected to two forces P=1800 and F=2500. Inner and outer radius of the pipe is 24 mm and 46mm, respectively. Calculate following unknowns for point A, (a) Find all stresses and show them on the oriented element, (b) principal stress and corresponding angle, (c) maximum shear stress. Take a = 100 mm, b = 150 mm and c = 75 mm.

Q: For the state of stress given in the Figure below determine the following: 1. the principal stresses…

A: Given:σx=18 MPaσy=-14 MPaζxy=12 MPa

Q: 3. Consider a cylinder with an outer Diameter, D = 4 m that is under a pressure p = 200 kPa and…

A: To determine the stresses on element A with the coordinate axis and to find the principal stresses…

Q: A roadway sign weighs 5.4 kN and is supported by a structural pipe that has an outside diameter of…

A:

Q: Draw the Mohr's Circle of the stress element shown in figure. Find:- 6 MРа A 6 MPa The stresses…

A:

Q: The figure shows the stresses at a point. Determine the principal stresses and the maximum shear…

A:

Q: A typical aluminum-alloy scuba diving tank is shown in the figure. The outside diameter of the tank…

A:

Q: Pravinbhai

A: The objective of the question is to determine the normal stresses σn and σk, and the shear stress…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 3700 psi, Sy =…

A: Find angle with vertical  to find the normal and shear stress at the given plane, θ= 90 - β= 90-49=…

Q: 2. Consider the Flamant solution - a line load on the edge of a half space. The valid stress…

A: according to a given question

Q: Using Mohr's circle, determine: (a) The stresses acting on an element oriented at an angle 0=-30°…

A: Mohr's circle shows the transformation equations of the issues of planar stress. It is helpful to…

Q: 2. A hollow generator shaft of 180-mm outer diameter and 120-mm inner diameter carries a torque T 40…

A:

Q: The thin-walled pipe has an inner diameter of 2 in. and a thickness of 0.1 in. It is subjected to an…

A:

Q: Force is applied to the pipe using a wrench as shown in the figure. The inner radius of the pipe is…

A: Given Data: Inner radius of Pipe ri=75 mm=0.075 m Outer radius of Pipe ro=100 mm=0.1 m Yield stress…

Q: The following stress element represents the stress state at point A of the structure in the figure…

A:

Q: The stress at a certain point is as shown in the figure. If the maximum in-plane shear stress…

A:

Q: 3. For the state of stress shown below, calculate the principal stresses and maximum shear stress.

A: σx = 90 Mpa σy = -60 Mpa Txy = 20 Mpa

Q: The surface of an airplane wing is subjectedto plane stress with normal stresses σx and σy andshear…

A: Consider σx and σy be the normal stress in x and y-axis respectively and τxy be the shear stress in…

Q: A typical aluminum-allóy scuba diving tank is shown in thế ngure. The outside diameter óf the tank…

A: Solution:

Q: Find the normal stress value on the new x-axis obtained by rotating the element with the stress…

A: Write the given data with suitable variables. σx=100 MPaσy=60 MPaζxy=45 MPa

Q: Calcuate Shear and Bending From Point A to Point B and Point A to Point C. Draw a FBD from point A…

A: For the solution refer below images.Find F.B.D. and shear and bending diagram for portion AB and…

Q: A steel pipe with an outside diameter of 4.67 in. and an inside diameter of 4.25 in. supports the…

A:

Q: The state of in-plane stress at a point on an element of material is shown. Let a₂ = 55.0 ksi, ay =…

A:

Q: = A machine component is fabricated from a bent tube as shown below. One part of the tube lies along…

A: Outside diameter, d0=122 mmInside diameter, di=108 mmForce F=8.5 kNLengths,L1=258 mmL2=118 mmL3=281…

Q: For the shown element, what are the principal stresses and their orientations (ew, cew), draw the…

A: (a) To find: The principle stress and the orientation of principle stress Given: The stress in…

Q: he stresses shown below act on horizontal and vertical planes through a point on the urface of a…

A: Part a): From the given data, the stresses in the respective directions are identified as, σx=0σy=-6…

Q: Concentrated loads of Px = 43 kips, Py = 29 kips, and P₂ = 52 kips are applied to the cantilever…

A: The concentrated load, Px = 43 kips, Py = 29 kips, Pz = 52 kipsThe dimensions, a = 7 in, b = 14 in,…

Q: Q5: - Draw the Mohr's Circle of the stress element 6 MPa shown in figure. Find: - A 6 MPa The…

A:

Q: The stresses on an element are o, = -300 psi and o „=-600 psi. Find the maximum shear stresses on…

A:

Q: The normal stresses at a point are o, = 80 MPa and oy = 20 MPa; the shear stress at this point is…

A:

Q: 4- The cross-section of the ABCD element in the figure is a circle with a diameter of 6 cm. The…

A:

Q: The tank shown with elliptical cross-section is fabricated from 14 mm steel plate. Determine the…

A:

Q: The cross-sectional area shown is subjected to V = 600 kN and M =1000 kN-m. What is the flexural…

A:

Q: find the stresses acting on an element oriented at 30° Clockwise

A: Given: Plane stress conditionσx=σ1=-4740150=-31.6 MPaσy=σ2=-4740100=47.4 MPaAngle of rotation 30°…

Q: The principal plane stresses and associated strains in a plane at a point are s1 = 36 ksi, s2 = 16…

A: Given: The values of principal stresses are s1=36 ksi and s2=16 ksi. The values of strains are…

Q: Find the maximum compressive and tensile normal stresses in the section given in the figure. Draw…

A:

Q: The stresses shown below act on horizontal and vertical planes through a point on the surface of a…

A: Part a): From the given data, the stresses in the respective directions are identified as, σx=0σy=-6…

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.