Find the maximum compressive and tensile normal stresses in the section given in the figure. Draw the graph of the neutral axis and normal stress next to the section.  Find the normal stresses in kg / cm2. P =16964 KG    EX=20 cm  EY=6 cm

Q: For the state of stress given in the Figure below determine the following: 1. the principal stresses…

A: Given:σx=18 MPaσy=-14 MPaζxy=12 MPa

Q: A rod of a variable cross-section shown in the following figure is subjected to two axial forces.…

A:

Q: Q2) For the problem shown in the figure, - Find the axial displacement at the end B - Determine the…

A: for solution refer below images.

Q: Q2: For the element shown in Figure 2. Use the data from Table 2 Determine the following: 1. The…

A:

Q: The dimensions of the beam with the cross-section are given as b, a, t as in the figure on the…

A: Given data The dimensions of the beam with the cross-section are given as b, a, t as in the figure…

Q: The forces as given below are applied as shown in the figure. F1=10 kN, F2=5 kN and F3=3 kN. The…

A: a)  -159.15 MPa(Compressive) , 35.80 MPa(shear stress) b) Principle stresses 7.686 MPa ,-166.836 MPa…

Q: The strains for an element of material in planestrain (see figure) are as follows:  εx = 480 X 10-6…

A: Given data as per question εx=480×10−6εy=140×10−6γxy=−350×10−6

Q: Find the normal stress and shear stress in the c-plane for the stressed member shown in the figure.…

A: Given figure    To determine the normal stress and shear stress in the c-plane for the stressed…

Q: he stress condition given in the figure, find the approximation o

A:

Q: 100 kN and 200 kN to the rectangular column in the figure Two forces act in intensity. A and B…

A:

Q: Find the stresses in each direction, also find the change in volume of the block of dimension 110 mm…

A: stress is defined as the force per unit area.

Q: The system in the figure consists of AB with a wall thickness of 5 mm and an outer diameter of dAB =…

A:

Q: 1.2-2 Calculate the compressive stress o, in the circular piston rod (see figure) when a force P =…

A:

Q: 1-13. An arrangement of three rods is used to suspend a 50 kN weight as shown in the figure. The…

A: Given DataW = 50 kNdAB = 200 mm = dBDdBC = 13 mm To find stress in rod

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 3700 psi, Sy =…

A: Find angle with vertical  to find the normal and shear stress at the given plane, θ= 90 - β= 90-49=…

Q: A homogenous rigid block subjected to the loading shown in figure is supported by three steel rod…

A: Given: Diameter of steel rod, d=25 mm

Q: as given below 80 mm a) Normal and shear stresses occurring at point A Find and show it on the plane…

A: Given: The diameter of the shaft, d = 20 mm = 0.02 m

Q: Determine the nodal displacements and the element stresses, including principle stresses, due to the…

A:

Q: The beam is supported by two wires AB and CD that have a diameter of 12 mm and 8 mm, respectively as…

A:

Q: .A rod is composed of three segments as shown in the figure and carries the axial loads P1= 120kN…

A:

Q: 2. A palm tree weighing P₁ = P₁ + P₂ is tilted at an angle of p (see the figure). The weight of the…

A:

Q: A solid steel bar with a diameter of 50 mm is subjected to three forces as shown in the figure,…

A: In the given problem, the main stresses will be developed at point B due to 1200N force which will…

Q: Two forces are applied to the bar shown in the figure. Determine: The normal and shearing stresses…

A: Calculate the moment acting about the centroid due to the two forces. M=6 kips×10.5 in-2 in+50…

Q: Find the normal stress value on the new x-axis obtained by rotating the element with the stress…

A: Write the given data with suitable variables. σx=100 MPaσy=60 MPaζxy=45 MPa

Q: To draw the internal normal force diagram, it is important to determine the internal normal force at…

A: Find internal force at point A Given data:- P1=4.5 kips P2=8 kips

Q: Determine the shortest distance d to the edge of the plate at which the force P can be applied so…

A:

Q: B = 30° A 50 mm

A: The moment of inertia about the y-axis and z-axis are determined as follows.

Q: 3) Objects 1 and 2 are positioned as shown in the figure. Object 1 is a rigid support. For object 2,…

A: Consider a body having length L,cross-sectional area A and Young's Modulus E is heated by ΔT°C.…

Q: 1-A bar of square cross section is subjected to point loads of P1, P2, P3 and P4 as shown here.…

A: Given data: Modulus of elasticity, E = 166 GPa. Draw a labeled diagram of the given bar. Apply…

Q: The round bar in the figure is made of steel (E-207 GPa). The load F has a magnitude of 100 N. You…

A: Young modulus of the material,(E)=207 GPa. Applied force (F)=100 N. Diameter of the shaft,(d)=20 mm.…

Q: The articular Cartilage is subjected to plane stress with normal stresses &x ,Oy and shear stress…

A:

Q: Calcuate Shear and Bending From Point A to Point B and Point A to Point C. Draw a FBD from point A…

A: For the solution refer below images.Find F.B.D. and shear and bending diagrams for portions AB and…

Q: 1. A loaded bicycle pedal crank is shown below. 18. 750 N (-7 direction) d A @ Top -y₁ B@ Top d = 15…

A:

Q: 4- The cross-section of the ABCD element in the figure is a circle with a diameter of 6 cm. The…

A:

Q: In the figure, the steel shaft with a diameter of 36 mm is 240 mm diameter pulley. Belts also formed…

A:

Q: 7.2-5 The stresses acting on element A on the web of a train rail (see figure part a) are found to…

A:

Q: An element in plane stress on the surface of an automobile drive shaft (see figure) is subjected to…

A:

Q: 5 KN / m A SIMPLE STRESSES 5 KN / m D 50 KN-m 5 KN / m F E 2. Points C and D of the 1.00 1.00 1.00…

A:

Q: Find the normal and shear stresses at points H and K, since F= 15 kN in the loading condition shown…

A:

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.