Determine the shortest distance d to the edge of the plate at which the force P can be applied so that it produces no compressive stresses in the plate at section a-a. The plate has a thickness of 10 mm and P acts along the centerline of this thickness. 300 mm Select your own P and use MATLAB to obtain your solution. 200 mm 500 mm

Q: 1300 m^3 to t

A:

Q: Find others Force applied =2.78N Area = 1mm?

A: Given data : Force=F Area=A   Required : Stress

Q: 3K/ft 12K IGK 16K 2K/ft a to tatat 8' 4' 4' 4! 4' 8'

A:

Q: 4 A water Pipe is to beconstructed with a 207, grade in the novth divection and a 10% grade in the…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: Find WAB шав using VA=VB+WAB Y VAID

A: Instantaneous center of velocity refers to any point on a rigid body or on its extension that has…

Q: 5 kN 120 9. Way 100 x 200 × 120 mm rubber block in size is placed on the U profile without any gaps…

A: E=12 GPaν=0.5Dimension of way of rubber block=100×200×120 mmF=5 kN

Q: AB, BC, CD, DE are each 2m long and the plane distance from A-D is 4m. Members are at right angles…

A:

Q: Cal culate the stress between the two rods at the weld if the weld has a radius of 0.5 inch and the…

A: Data given- For part a) Small rod Area = 1.0''× 1.5" Tensile load = 50 kips Radius (r) = 0.5 inch…

Q: The jet plane is traveling with a speed of 120 m/s which is decreasing at 40 m/s² when it reaches…

A: According to the given dataWe need to find Acceleration of the jet at point-A and its direction of…

Q: Calculate the stress concentration factor (kt). the small diameter is 0.88 in and the bigger one is…

A: Given:The small diameter is the bigger diameter is The radius is The moment is The torque is

Q: 1. A capacitor of 3.23µF has an area of 6.35mm^2. Determine the separation distance between the two…

A:

Q: As shown in the figure, the forces P1 and P2 are applied to the end A of the rod AB welded to the…

A:

Q: u=7i-9j, w=-i-6j find w-u

A:

Q: A 7m 20KN/m TATI + B 10kN/m 3m с V/M, N @ MID POINT OF POINTS A & B

A:

Q: Derive the following formula for the distancee from the centerline of the wall to the shearcenter S…

A:

Q: Calculating the Stress Tensor Conditions Oz = 40 MPa Ox = 20 MPa Planes pass through point P at 10°…

A:

Q: 10 95 MPa 10 cm 5 cm

A: To Find : Maximum Stress in Plate =?

Q: 48.0 in. and the wall thickness is 0.75 in. The tank is pressurized to 1.40 ksi. Determine the a

A:

Q: A 12-inch diameter standard weight fire sprinkler pipe will be supported from the roof framing of a…

A:

Q: For the H- section shown, Find the value of h so that I = ly. 20mm 100mm | 20mm h = ? 20mm 140mm

A: Draw the given H-section. Since the given H-section is symmetric, the centroid will lie in the…

Q: explain this pressure or in distress The Muslim is ribs In Figure (1) and do shown Muslim ribs…

A:

Q: Sketch the distribution of shear stress across the diameter of the blood vessel.

A: It is asked to sketch the shear stress distribution in blood flowing through a blood vessel

Q: Help me determine   Maximum  shear stress

A: Given data : Normal stress in X direction σX=-12 MPaNormal stress in Y direction (σY)=0 MPaShear…

Q: 4. A 2-slug mass is dropped from an airplane with initial downward velocity zero. Find v(t) for t≥ 0…

A:

Q: Draw SFD BMD V(x) M(x)

A: To draw:The shear force and Bending moment diagram.

Q: Р.3) 0.75 m long and angled at 0 = 30° with respect to Link AB of the illustrated system is "BIA,…

A:

Q: Find the welouty f flay A=2.1m2 = २० 0[S

A: Introduction : The question is related with fluid mechanics . In this question we are provided with…

Q: What would be the Technique to find the value of 'd' in this equation? I mean Show the…

A:

Q: Find the work done Force=0.433 N Displacement=0.22 m

A: Given data : Force=F Displacement=d   Required : Work done

Q: Find ly

A: To find the length ly, we need to use the Pythagorean theorem. Let's break down the problem and…

Q: In a triaxial compression test, for drained condition the confining pressure is 200 kPaand deviator…

A: Triaxial compression test, Calculate the net shear stress at the initial condition.

Q: Given: P=1.8a kN Area(BE)-150a mm? Area(CF)=150a mm? E=200 GPa Required: Change in length of CF? 18a…

A: Assuming, a=0

Q: Convert 589 mm to m.

A: Given Data : Length (L)=589 mm

Q: W = 15kg %3D B 1.5m Im VHA 5m

A:

Q: 10bar = 1MN/m? Select one: O True O False

A:

Q: The maximum EIY is. . N.m^3

A:

Free undamped vibrations

Whenever an object/system displaces in either side of its equilibrium position with the help of an external/internal means, then the object/system moves regularly or randomly on both sides of its equilibrium position. This motion is called vibration. Generally, there are three types of vibration: longitudinal vibration, transverse vibration, and torsional vibration.