A cap plate at the bottom of the brace distributes the load P = 660 kN to four flange plates (thickness, tf = 22.5 mm each) through a pin (diameter, dp = 55 mm) to two gusset plates (thickness, tg = 34 mm).[FS = 1.5 , σu = 250 MPa, τu = 400 MPa] Determine the shear stress in the pin? The answer in MPa Determine the bearing stresses in the gusset plates? In MPa Determine the bearing stresses in the flange plates? In MPa Determine the maximum allowable load P that can be applied to this connection if the required factor of safety is FS and theultimate normal and shear stresses in the plates are llimited toσu and τu, respectively?

Q: Q7-Q8: A 6-in.-long bronze tube, with closed ends, is 3 in. in diameter with a wall thickness of…

A: Longitudinal Stress, σlong = σx = 15 ksi. Tangential Stress, σtang = σy = 45 ksi.

Q: The pressure of the fluid is p N/mm2 by gauge. Determine suitable thickness of the cylinder wall…

A:

Q: This is a question from the textbook, Example 3.1 from page 132. We are interested in the…

A:

Q: Compute the max load (P ) if the stress in steel 120 Mpa and in bronze 70 Mpa steel bronze A= 300mm2…

A: Given: The maximum allowable stress in steel rod = 120 MPa The maximum allowable stress in bronze…

Q: A cylindrical pressure tank with an outside diameter of 100 mm and a wall thickness of 5 mm is…

A: outside diameter do= 100mmthickness t= 5mminside diameter di=do-2 t= 100-2*5=90mmload applied P= 40…

Q: Elastic Recovery After Plastic Deformation A cylindrical specimen of a brass alloy 6.8 mm (0.27 in.)…

A: Stress is the ratio of force per unit area having the unit of N/m2 in SI system. Strain is the ratio…

Q: 3. As in the figure, a ship can move both with the wind and with a diesel engine. your ship The mast…

A:

Q: P MATHalino.com -12 in- -6 in 6 in F 3 in A 13 in B 12 in- 2 in 6 in Cross- Section

A: The value of forces are

Q: From the figure shown, the tube has an outer diameter of 80 mm and an inner diameter of 70 mm.  The…

A:

Q: The rectangular bar is connected to the support bracket with a circular pin, as shown in the figure.…

A: Bar width, w= 2.25 in Bar thickness, t= 0.375 in Pin diameter, d= 0.775 in Applied load, P= 4800 lb…

Q: A point On a free surface of a machine point (E = 214Gpa, G= 83Gpa) the stress state is shown on the…

A: GIVEN :- E = 214Gpa G= 83Gpa σy=15 MPaσx=-30 Mpaζxy=25 MPa

Q: Ql: A bar ABCD shown in Figure (1) below consists of three sections: AB is of 42 mm diameter and 80…

A:

Q: 3. Compute the shear stresses. At the top of the side wall the thickness, 1, is 24 in. The torsional…

A:

Q: 4. The three bars are made of steel and form a pin-connected truss. Each bar has a cross sectional…

A: Given: A=3 in2Est=29×106psiT0=50 FTf=110 Fα=6.6×10-6ft/ftF

Q: Determine the internal forces at point J for the structure shown, where member BD can only carry…

A:

Q: a) The normal stress in bar BD is most nearly b) The shear stress in the pin at D is most nearly…

A:

Q: Q1/ The aluminum and bronze cylinders are centered and secured between two rigid end-plates by…

A:

Q: 800 N 120 N.m d = 8 cm 600 N Q /If the cross section of the femur can be approximated as a circular…

A: Stress due to eccentric axial load of 800N P1=P2=800N P2 and 800N will create a moment M=800(0.8)=64…

Q: Rockwell hardness . figure 6.19 Rockwell hardness Tensile strength = 0 MPA Tensile strength = 0 ksi…

A: (a)

Q: Problem I. In a high-rise building construction, a boom is being used to efficiently transport…

A:

Q: At a party, a parent is blowing up a birthday balloon until its diameter is n = 3.4 times the…

A: Introduction In this problem, we will compute the normal stress in the balloon after inflation, for…

Q: Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square…

A:

Q: As shown in the figure, a pressure force of P = 55000 daN acts on a pipe with an outer diameter of…

A: Given data :-

Q: A Belleville spring is made of silicon steel. The spring is compressed completely fl at when it is…

A: Given Force = 4500 N Allowable stress = 1375 × 106 N/m2 do/di =1.75 h/t = 1.5 To find Thickness of…

Q: Jason took a steel rod, 15.29-mm in diameter, and held snugly (but without any initial stress)…

A: Given: The diameter of rod, D = 15.29 mm The coefficient of thermal expansion, α = 13.6x10-6 mm/mmoC…

Q: A cylindrical hollow tube with closed ends is pressurized to a gauge pressure of 10 MPa and twisted…

A:

Q: Check whether the A-A section is safe in the hand vice in the figure. 2mm diameter 8mm size copper…

A: Given: The allowable stress for material, Sall = 140 MPa The moment of inertia about x-axis, Ix =…

Q: The shear force of section K in the structure is F

A: GIVEN:

Q: 1)In a thin plate, the state of stress prevails according to the figure. Calculate the principal…

A: Only one question is allowed to solve as per the guidelines.

Q: determine the internal loadings at points A,B and.

A: AD is essentially is a cantilever beam with UDL and point load at the end.

Q: Concentrated loads of Px = 43 kips, Py = 29 kips, and P₂ = 52 kips are applied to the cantilever…

A: The concentrated load, Px = 43 kips, Py = 29 kips, Pz = 52 kipsThe dimensions, a = 7 in, b = 14 in,…

Q: Three parallel vertical rods of equal length (L-2m) support a rigid beam AB to which a force…

A:

Q: Determine the bolt stress for an internal pressure of 500 psi.

A: Given dataequally spaced steel bolt the diameter of the bolt the pre-load of each bolt  the number…

Q: Determine the shear stress in pin A shown in the figure below. The load, P is equal to 10 kN. All…

A:

Q: SN= 50 lbs FN= 104 kips

A: To find stress in cable CD

Q: QI/ For the assembly below, determine the average normal stress for the cable. Assume that the cable…

A: Given Data  Load, P=12 KN d=10 mm Let us draw all the reactions

Q: The stresses at a given point in a stressed body relative to rectangular axes are a=20, dy=-40, 0₂ =…

A: Given stress components:The angles according to x,y, and z-axis is given as:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.