(ksi) Ty = 50 у (гad) 0.004 -P P-

Q: cylindrical rod subjected to an uniaxial tensile load P as shown, given P = 800 (N), the original…

A: The cylindrical rod with 8 mm diameter and 60 mm length is subjected to an uniaxial tensile load of…

Q: The bar shown in the following figure has a diameter of 40 mm and is subjected to a force P = 4500 N…

A: The Point A will be subjected to tensile stress due to bending stress generated by force F.bending…

Q: in the figure. Also, determine the factor of safety for the tank based on Von-Misses and Tresca…

A:

Q: et's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a…

A:

Q: Problem 4: The gap between the support and bar BC is 0.01 inches. If the magnitude of the force…

A:

Q: Three metal rods are firmly attached to the walls and the middle rigid plate. Rod AB is made from…

A:

Q: Two hard rubber blocks [G = 367 kPa] are used in an antivibration mount to support a small machine,…

A: Given Data  LOad =948 N a=20 mm  b=50 mm c=80 mm Two shearing surface SHear area =2bc=2(20)(50)=2000

Q: If an isotropic material has a shear modulus of 11 Gpa and a Poisson's ratio of 0.34, calculate its…

A:

Q: A solid circular rod 200 mm long and 20 mm in diameter has an axial force of P. are exposed. The…

A: Rod length, L= 200mm=0.2m Rod diameter, d=20mm=0.02m Force, P=550 N Extension in rod,…

Q: Two bars are used to support a load. When unloaded, AB is 5 in. long, AC is 8 in. long, and the ring…

A:

Q: The bulk modulus of the steel bar with modulus of elasticity 1.8x105N/mm2 and Poisson’s ratio 0.25…

A:

Q: 1-A solid axial member which is made from three parts with different materials (sections 1 and 3) is…

A: I have used the first row for the values of youngs modulus. NOTE: According to Bartleyby's policy we…

Q: A solid circular rod 200 mm long and 20 mm in diameter has an axial force of P. are exposed. P = 300…

A: Given data: Length of the circular rod, L = 200 mm. The diameter of the rod, d = 20 mm. The…

Q: the contraction of the bar

A: Given ; A steel bar of;     ⇒   40mm2×40mm2cross-section is subjected to an axial compressive load,…

Q: For the structure below, calculate the diameter of the pin G, considering that its allowable stress…

A:

Q: hand written plz i'll upvote Shown in the figures (1) and (2) are trusses containing members that…

A: To choose: The correct option. Given: The modulus of elasticity of material of the members are same…

Q: The elastic portion of the stress- strain diagram for the 2014-T6 aluminum is shown in the figure. A…

A:

Q: The figure below shows the cross section of a steel rectangular tube, of uniform thickness t= 25 mm,…

A:

Q: 3. A cylindrical metal rod of 50mm diameter and 3m length is subjected to a tensile load of 150KN.…

A: Strain is the deformation in the material per unit length. True strain is the natural log of the…

Q: &=13µm decrease in the bolt diameter d. Bolt rties are given as G=77 GPa and v=0.3. ine the internal…

A:

Q: A thin metal alloy plate is loaded by biaxial stress (2 directions) given by 8000 psi in the x…

A:

Q: he bar shown in the following figure has a diameter of 20 mm and is subjected to a force P = 2750 N…

A: Given:d=20 mmP=2750 NF=14000 NSyt=480 MPaPoint A will be subjectd to tensile stress due to bending…

Q: 2. The composite bars shown are firmly attached to unyielding supports. Determine the load P if the…

A: For the given composite beam  horizontal movement = 0.272 mm    To determine  Value of load P if…

Q: The stress concentration occurs whenever there is an abrupt change in the cross-section of a…

A: Stress concentration Factor (k) : it is defined as the localisation of higher stresses due to…

Q: If the A-36 solid steel rod has a diameter of 50 mm and has been loaded with loadings as shown in…

A: In this question, we have to find the state of stress on the given points. This means that we have…

Q: Assuming that the load P = 120 KN is carried equally by the four rivets in the figure showing the…

A: Solution: a) Shear force in each rivet=P4=1204=30kN  Since the rivets are in double shear, the shear…

Q: A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the…

A: The change in length of a bar can be expressed as,

Q: The shear stress-strain diagram for an alloy is shown in the figure below (Figure 1). Take ✓ = 0.3.…

A:

Q: The rods A and B having a tensile stress of 400 N/mm², determine the diameter so that they can…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: 2. A bar having a length of 5 in. and cross-sectional area of 0.8 in? is subjected to an axial force…

A: Given:L=5 inA=0.8 in2F=8000 lb∆L=0.003 in

Q: An axial element that is subjected to force P is connected by two plates and 4 bolts as shown in the…

A:

Q: The d = 14-mm-diameter solid rod passes through a D = 19-mm-diameter hole in the support plate. When…

A: Given: The diameter of rod is .The diameter of hole is .The plate thickness is .The head diameter of…

Q: Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was…

A: Option - B => 0.0241 mm => Total Deformation on the brass

Q: 2. A circular steel bar with with a diameter of 3 in and length of 2 m is subjected to an tensile…

A: Given data: d=3 in=0.0762 mL=2 mF=80 kNG=200 GPav=0.32 Need to determine the change in length and…

Q: A machine member part is subjected to fluctuating stress of σ = ax cos(8nt) The endurance limit of…

A: Given:Fluctuating stress, σ=σo cos8πtendurance limit=350 MPAFOS=3.5Find,maximum value of  σo

Q: A steel column with an outer diameter of 50 mm and an inner diameter of 40 mm surrounds a solid…

A:

Q: A steel rod with length equal to 12 ft, has a diameter of 0.8 inches in quarter of its length and a…

A:

Q: The bar shown in the following figure has a diameter of 40 mm and is subjected to a force P = 1500 N…

A: Given:F=500 NP=1500 Nd=40 mmSyt=60MPaI=π64*404  =125663.70 mmStresses acting at point A:The Force…

Q: The stepped rod shown in the figure is made of Al 2014-T6 aluminum alloy. At temperature T1 = 20°C,…

A:

Q: The two bars shown in the figure are used to support a load P. When unloaded, joint B has…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.