Learning Goal: The element of material below is subjected to the state of stress shown, where a = 102.0 MPa, b = 52 00 MPa, and c = 22.00 MPa (Eigure 1) Figure L. < 1 of 1 > Y Determine the orientation of the planes of maximum and minimum normal stress, 0p1 and 0,2. respectively. Use the value for 0,2 that is negative. Then use this value to determine the value of Opt Express your answers to four significant figures separated by a comma. ▸ View Available Hint(s) Opl, Op2 = Submit [ΨΕΙ ΑΣΦ Part B - In-plane principal stresses 01 02 vec 3 Ĉ Determine the in-plane principal stresses for the element (as oriented in Part A), and calculate 1 and 2 such that they correspond with 81 and 0,2 Express your answers to four significant figures separated by a comma. ▸ View Available Hint(s) ΠΡΕΙ ΑΣΦ11 | vec 6 a O BKK ? W ? B MPa, MPa

Learning Goal: The element of material below is subjected to the state of stress shown, where a = 102.0 MPa, b = 52 00 MPa, and c = 22.00 MPa (Eigure 1) Figure L. < 1 of 1 > Y Determine the orientation of the planes of maximum and minimum normal stress, 0p1 and 0,2. respectively. Use the value for 0,2 that is negative. Then use this value to determine the value of Opt Express your answers to four significant figures separated by a comma. ▸ View Available Hint(s) Opl, Op2 = Submit [ΨΕΙ ΑΣΦ Part B - In-plane principal stresses 01 02 vec 3 Ĉ Determine the in-plane principal stresses for the element (as oriented in Part A), and calculate 1 and 2 such that they correspond with 81 and 0,2 Express your answers to four significant figures separated by a comma. ▸ View Available Hint(s) ΠΡΕΙ ΑΣΦ11 | vec 6 a O BKK ? W ? B MPa, MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Solid Mechanic Chapter 5 (Stress Transformation Equiation) please show the full calculation. Thank you
A steel bolt of 6 mm in diameter has a tensile load of 40 kN. Find the average tensile stress at the section M and the screwed section N. where the diameter at the root of the thread is 4 mm as shown in Figure Q1.2. M -40KN 40KN4- 4 mm diameter 6 mm diameter
L,=40mm; L,= 120mm; L=100mm and 0,=65°. Find the possible value of 0, and 0, L,=80mm and 3.
ans c please fast
Q: The soil element with known stress conditions is shown in following figure. (i) construct Mohr's circle for the soil element and determine (ii) stress condition of the plane AC (use double angel method); (iii) major and minor principal stresses; (iv) the angle between major principal plane and the plane "AD" ; (v) maximum shear stress. Provide your answer up to one decimal point. [use graph paper to draw Mohr's circle] 2 kN/m² 6 kN/m² + + B D 2 kN/m² 2 kN/m²
Consider the frame in (Figure 1). The crate weighs 400 lb. Follow the sign convention. Figure 4 ft A B 1.5 ft 1.5 ft 1.5 ft 1.5 ft F /C . E 0 D 0.4 ft < 1 of 1 ▼ Part D Determine the normal force at point E. Express your answer in pounds to three significant figures. NE = Submit Part E VE = Submit Determine the shear force at point E. Express your answer in pounds to three significant figures. Part F [5] 195| ΑΣΦ | 11 | vec 4 Request Answer ME = Π| ΑΣΦ I Request Answer vec Determine the moment at point E. Express your answer in pound-feet to three significant figures. [V=| ΑΣΦ www. vec ? ? ? lb lb lb-ft
Plz solve correctly
The two rods (A-B and B-C) shown in the left panel are connected by pins at A, B, and C. The cross sections of A-B and B-C are 10mm×13mm and 10mm×10mm, respectively. The bilinear stress-strain relation shown in the right panel is for the material used to make the two rods, where Ei is the slope of the stress-strain curve for stresses between 0 and 80 MPa and E2 is the slope for stresses larger than 80 MPa. Note that Hooke's law is only valid for stresses up to 80 MPa. A 1 1 B 0.900 m 3 P = 30 kN 2.44 m C σ MPa 80 E₂ = 40 GPa E₁ = 80 GPa E a) Given the conditions above, find the axial elongation for each rod when subjected to P=30KN. b) Find the final position of Point B due to the applied load P at that location. Hint: Assume point B moves by unknown amounts Ax and Ay from its initial position, and then use right triangles to write the known final lengths of the cables in terms of Ax and Ay. The equations can be simplified by assuming terms Ax² and Ay² are so small they can be…
3) Solve the plane stress problem using two-element model to find displacements and stresses. 15 kN 30 mm E-70 GPa Thickness - 10 mm
solve all 3
A rectangular column (blue color) is fixed to a rigid ground (brown color). As shown in the figure, the column is under two external loadings at C. Determine the state of stress at point K of the column and represent the stress components on a stress element.
Write the solution for the following: Member BC= 600 N Member FG = -600 N