A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 7 m long, fixed at the top and bottom, and has additional support in the weak direction 3 m from the top. Properties of the section are: A = 14,500 mm² , Ix = 258.6 x 106 mm“, Iy = 84.375 x 106 mm* 1. Calculate the critical slenderness ratio of the member. A. 26.208 С. 36.706 В. 45.882 D. 27.529 2. Calculate the nominal axial load capacity of the column. A. 3 104 kN C. 4 213 kN B. 4 851 kN D.5 344 kN 3. that of the dead load. Use LRFD. Calculate the service axial dead load if the service axial live load is twice as A. 1 354 kN C. 1 093 kN B. 992 kN D. 634 kN

A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 7 m long, fixed at the top and bottom, and has additional support in the weak direction 3 m from the top. Properties of the section are: A = 14,500 mm² , Ix = 258.6 x 106 mm“, Iy = 84.375 x 106 mm* 1. Calculate the critical slenderness ratio of the member. A. 26.208 С. 36.706 В. 45.882 D. 27.529 2. Calculate the nominal axial load capacity of the column. A. 3 104 kN C. 4 213 kN B. 4 851 kN D.5 344 kN 3. that of the dead load. Use LRFD. Calculate the service axial dead load if the service axial live load is twice as A. 1 354 kN C. 1 093 kN B. 992 kN D. 634 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A round steel rod made of structural steel, AISI C1118, As rolled is to be used as a column, centrally loaded with 15 kips; N= 2.75. Determine the diameter for (a) L= 20 in. (b) L= 5 in. (c) the same as (a) and (b) except that the material is AISI 9850, OQT 1100 F. Is there any advantage in using this material rather than structural steel?
Uuestion 1: Calculate the axial load of spiral column with respect to first and second peaks. Materials used are C25 and S420 for longitudinal bars of 8- 024 and for spirals. Use the design strength of concrete and steel. 2. A, fywk 0, = D (s) 4. Ao P. = D (s) fa = f+4.0-0, GAP fa 4. f ynk (A min p, = 0.45. , min p, = 0.12. ywk D=550 mm H=600 mm Spiral : 010/85 mm 200 mm
A hallow cylindrical steel column with an outer diameter of 200 mm and an inner diameter of 180 mm is subjected to a compressive load of 200 kN. The yield strength of the steel is 250 MPa. Calculate the factor of safety for the column using the maximum normal stress theory.
A 12” X 16”simply supported pine wood beam is being considered to carry a uniform load distribution across a span of 12’ as shown. In addition to the uniform load, the beam is also subjected to a tensile load of 20 kips. If the ultimate tensile stress in pine wood is 4500 psi, determine whether the beam is considered safe according to the Allowable Stress Method, using a Factor of Safety 2.5. Hint: you can calculate the maximum tensile stress in the cross-section without having to use Mohr’s circle
The part shown is loaded at point C with 290 N in the positive x direction and at point E with 200 N in the positive y direction. The diameter of the bar ABD is 12 mm. Evaluate the likelihood of failure in section AB. 55 dia, d B Q ********* where P= 290 N, Q = 200 N, and d = 12 mm NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.
A 500 mm long rotating shaft has a groove in the middle and carries a 2 kN transverse force at section C as shown. The shaft is made of a high carbon steel with a yield strength of 965 MPa and an ultimate tensile strength of 965 MPa (140 ksi). The bearings at the shaft ends that can be modeled as simple supports. The shaft has a machined surface finish. Determine the: (a) Fully corrected endurance limit for this shaft. (b) Fatigue strength for this shaft at a life of 250,000 rotations. (c) Fatigue stress concentration factor for the groove at section B. (d) Infinite life fatigue factor of safety at section B. (e) Infinite life fatigue factor of safety at section C. (f) Finite life fatigue factor of safety at section B for a life of 250,000 rotations. (g) Finite life fatigue factor of safety at section C for a life of 250,000 rotations. Assume a reliability of 50% and no temperature effects. 40 points 2.0 kN r= 2.5 mm. 25 mm 27.5 mm 250 mm 180 mm A В C 70 mm Answers (а) Sn (MPa) (b)…
A tensile-testing apparatus is to be constructed that must withstand a maximum load of 293516 N. The design calls for two cylindrical support posts, each of which is to support half of the maximum load. Furthermore, plain-carbon(1045) steel ground and polished shafting rounds are to be used; the minimum yield and tensile strengths of this alloy are 343 MPa and 565 MPa(82,000 psi), respectively. Specify a suitable diameter in mm for these support posts. Assume safety level is 2.3. Round your answer to 2 significant figures.
Answer is Not 43,-1 and 22.
I need help solving this problem
The assembly consists of two red brass C83400 copper rods AB and CD of diameter 30 mm, a stainless 304 steel alloy rod EF of diameter 40 mm, and a rigid cap G. The supports at A, C and Fare rigid. Modul of elasticy for the copper is Ecopper = 101 GPa. Modul of elasticity for the steel is Esteel = 193 GPa. (Figure 1) Figure Part A OAB = Submit Part B OCD = Submit Part C Value μÅ Request Answer Determine the average normal stress developed in the rod AB. Express your answer to three significant figures and include the appropriate units. TEF Value μA Request Answer Submit Units 19 Units FA Determine the average normal stress developed in the rod CD. Express your answer to three significant figures and include the appropriate units. O μА -300 mm- Value 30 mm 30 mm Request Answer ? B G ? E 450 mm 40 kN Determine the average normal stress developed in the rod EF. Express your answer to three significant figures and include the appropriate units. 40 kN 40 mm Units MELL < 1 of 1 ?