The composite bar, firmly attached to unyielding supports, is initially stressfree. What maximum axial load P can be applied if the allowable stresses are 10 ksi for aluminum and 18 ksi for steel?

Q: 1.3 Determine the length of side a and the measure of the two acute angles. 72.0' 67.3'

A: find the side a and two acute angles.

Q: The cylindrical gasoline tank on a tractor is 11 inches in diameter and 36 inches long. How many…

A:

Q: How much force in lbs will it take to lift a 10 -lb weight with a wheel and axle, when the axle is…

A:

Q: Find in inches the inside diameter of this water pipe for an automatic icemaker. Express the answer…

A: Given     Outside diameter, d = 1 1/4 in                                  = 1.25 in…

Q: A steel beam, of lengths a = 4 m and b=4 m and a hollow box cross section, is supported by a hinge…

A: A steel beam, of lengths a = 4 m and b = 4 m and a hollow box cross section, is supported by a hinge…

Q: 8. This sheet metal section has 5 sets of drilled holes: A, B, C, D, and E. The holes within a set…

A: Given: The set of holes are equally spaced in horizontal direction. The five sets of drill holes are…

Q: I'm playing a game of pool with by brother; he's stripes. At some point, I notice I have a…

A: V = 6 oz = 0.17 gd = 2.25 inches = 0.057 me = 0.95  "coefficient of restitution" "coefficient of…

Q: What would it be in celcius

A: From the result, the final temperature of the air in the tank is 277.3 K

Q: In the scale of inches, draw material edge at 7.00 diameters with six holes at 50 diameters. The six…

A:

Q: A wind turbine has a power coefficient C, = 0.46 and is able to generate 1.6 MW. What was the amount…

A:

Q: A Prony brake with a 12” arm is applied to an engine flywheel. At 1200 rpm, the scale registers 20…

A:

Q: 1500# 1500# 1500# 1500# 12' K I

A: In this problem, following steps will be taken 1. Determine the reactions at the supports.' 2. Using…

Q: A wind turbine has a power coefficient C, = 0.25 and %3D is able to generate 1.3 MW. What was the…

A: Given    Wind power generated, P = 1.3 MW                 Power coefficient = 025

Q: A spring is 15 in. long when loaded with 16 lb and 6.5 in. long when loaded with 25 lb. Determine…

A:

Q: The horsepower (hp) that a shaft can safely transmit varies jointly with its speed (in revolutions…

A:

Q: A midsized Dozer weighs 41,000 pounds and has 175 hp. If the machine is working at 80% efficiency…

A: Given Data The weight of the machine is: W=41000 lb The power is: P=175 hp The efficiency of the…

Q: Consider the crank assembly of the figure. The bearings at points A and B are in good alignm…

A:

Q: The beam in the figure below is subjected to a load P= 3.9 kN at its end. Young's modulus is 210 GPa…

A:

Q: A shift lever ball has diameter 2.535 in. What is its volume in cubic inches

A: Given   Diameter, d = 2.535 in       Radius, R = 1.2675 in Find    Volume, V

Q: . Circle the letter corresponding to the view on the right that shows the result of rotating the…

A: According to the given details provided, we need to identify the view on the right that shows the…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.