The A-36 steel plate has a thickness of 12 mm. If there are shoulder fillets at B and C, and allow = 150 MPa determine the maximum axial load P that it can support. Express your answer with the appropriate units. P= Value Submit Request Answer Units ?

The A-36 steel plate has a thickness of 12 mm. If there are shoulder fillets at B and C, and allow = 150 MPa determine the maximum axial load P that it can support. Express your answer with the appropriate units. P= Value Submit Request Answer Units ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 10. The A-36 steel plate has a thickness of 12 mm. If there are shoulder fillets at B and C, and O allow = 150 MPa, determine the maximum axial load P that it can support. The maximum stress at the fillets can be determined from the formula Omax = K Gave, where K is the stress concentration factor for fillets given in Graphs in Section 4.7 of Hibbeler textbook, and based on the fillet radius to small width and large width to small width ratios. Also compute its elongation neglecting the effects of the fillets. 60 mm P A B r = 30 mm 200 mm 120 mm 800 mm r = 30 mm 200 mm 60 mm P
The thickness of the plate is t and the diameter of the pin is d. What is the correct area formula for determining the bearing stress between the pin and the steel plate? P pin Steel plate Support W
Determine the state of stress acting at point D. Take P₁ = 120 kN and P₂ = 45 kN. (Figure 1) Figure L -1.5m- +1.5m-1.5 m- 0.5 m 40 mm 100 mm 60 mm 80 mm 1 of 1 > Find op- Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. od= - 154.88 Submit Part B Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining MPa Find TD- Express your answer to three significant figures and include the appropriate units. JA TD= Value Units ?
The copper bar is subjected to a uniform loading shown in Fig. 10–24. Ifit has a length a = 300 mm, width b = 50 mm, and thickness t = 20 mmbefore the load is applied, determine its new length, width, and thicknessafter application of the load. Take Ecu = 120 GPa, ncu = 0.34.
please box in the following answers: normal stresses for beam AB and BC (mid section) normal stresses for beam AB and BC (at connections A and C) shear stress for pin A, B and C bearing stress along member AB and BC at pin section for A and C 600mm Flat end 40 mm FRONT VIEW d-25 mm d-25 mm 50 mm 125 mm 30 mm 25mm ,20 mm TOP VIEW OF ROD BC -800 mm Q-30 kN TOP VIEW OF BOOM AB d=25mm Flat end Q-30KN 20mm 20 mm END VIEW 600 mm 50 mm 20 mm 800 mm 30 AN 1
Question 5 of 5 View Policies Current Attempt in Progress For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the load is P = 60 kips. O 27.2 ksi O 37.5 ksi O 25.8 ksi O 21.9 ksi O 35.3 ksi
The bolt AB in (Figure 1) has a diameter of 18 mm and passes through a sleeve that has an inner diameter of 42 mm and an outer diameter of 52 mm. The bolt and sleeve are made of A-36 steel and are secured to the rigid brackets as shown. If the bolt length is 220 mm and the sleeve length is 200 mm, determine the tension in the bolt when a force of 50 kN is applied to the brackets.
A tensile force of 100 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to2.01 m. The true axialstrain is?
E. Rigid bar AD is horizontal before the weight of 112 lb is applied to the end of wire BC at C. The wires have a radius of 0.025" and are made of A913 steel. Determine the rotation of AD and how far C will move down due to application of the weight See Appendix of text for any material properties needed. Ans: 0.00071 radians 3 ft - 2 ft -3 ft- D B 4 ft W
A small stepladder has vertical rails and horizontal steps formed from a C-section aluminum channel. Two rivets, one in front and one in back, secure the ends of each step. The rivets attach the steps to the left and right hand rails. A 225 lb person stands in the center of a step. If rivets are formed of 6061-T6 aluminum, what should be the diameter d of the rivets? Use a factor of safety of 8 and round your answer to the nearest 1/16 of an in.
Part A The strut is supported by a pin at C and an A-36 stoel guy wire AB. (Eigure 1) If the wire has a diameter of 4.8 mm, determine how much t stretches when the distributed load acts on the strut. Express your answer three to significant figures and include the appropriate unita. ? SAn = Value mm Figure 3AANm 27 m
Problem 2 You will be determining the value for the external load P that will cause the diameter of BC to change to 5.8 mm. The original diameter of BC is 6 mm. Use the values given below unless otherwise stated by the questions. E = 200 GPa V = 0.38 300 mm 400 mm B 1 -200 mm-