x-: The tongs are used to grip the ends of the drilling pipe P. If a torque (moment) of Mp = 900 lb- ft is needed at point P to turn the pipe, determine the cable force F that must be applied to the tongs. Set 0 = 40°. (1 ft = 12 in.) 6 in. Mp 43 in. x- For question (Q2) above, if 0 = 80°, what do you think the cable force will be? (Circle one)

x-: The tongs are used to grip the ends of the drilling pipe P. If a torque (moment) of Mp = 900 lb- ft is needed at point P to turn the pipe, determine the cable force F that must be applied to the tongs. Set 0 = 40°. (1 ft = 12 in.) 6 in. Mp 43 in. x- For question (Q2) above, if 0 = 80°, what do you think the cable force will be? (Circle one)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. The hinged door shown has a chain attached at point C connected to point B. It has a tension force of 250 N. To maintain the door in that position shown, what is the magnitude of the moment of the axis where the hinges are attached? 2.5 m 1.5 m Fc = 250 N. 30 1 m 0.5 m
4) Determine the total moment caused by the forces Fp4 and Fca about the plate diagonal that goes through point B (the dashed line). Write your answer in cartesian vector notation. FCA= 500 lb 14 ft FRA = 350 Ib FDA= 400 lb 3 ft-> 3 ft 3 ft 2 t 6 ft
Compute the moment (positive if counterclockwise, negative if clockwise) of the 0.36-lb force about the pivot O of the wall-switch toggle. F = 0.36 lb 11° A 0.730" Answer: Mo = i lb-in.
Example An experimental device imparts a force of magni- tude F = 225N to the front edge of the rim at A to simulate the effect of a slam dunk. Determine the moments of the force F about point O and about point B. Finally, locate, from the base at O, a point C on the ground where the force imparts zero moment. 900 mm 700 mm %3D 300 mm 3050 mm
The cable that suspends the 132 kg mass wraps over the pulley with center C and ties off at E. The pulley has negligible radius. (Assume that the +x-axis is to the right and the +y-axis is up along the page. |132 kg 3.2 m 2.4 m 2.4 m Determine the force that pin A exerts on bar ABC, and determine member force BD. (Enter forces in kilonewtons.) A magnitude kN direction magnitude kN direction magnitude kN sense compression Determine the force that pin C exerts on bar ABC. (Enter the magnitude in kilonewtons and the direction in degrees counterclockwise from the +x-axis.) magnitude kN direction ° counterclockwise from the +x-axis
The rigid pipe is subject to the following loads. Neglecting the weight of the pipe, determine the moment at O. SOLVE THE FF 1. Vector component form of 50-lb force (ANSWER: 25.000i +0j -43.30k lb) and the Moment at point O, in vector component form. (ANSWER: 1153.01i -829.52j +250.00k lb-in) 2. Magnitude of the resultant force (ANSWER: 78.10 lb) 3. Position vector of the 50-lb force from point O to its point of application on the pipe. (ANSWER: -15i -10j +12k inch)
Compute the moment (positive if counterclockwise, negative if clockwise) of the 0.32-lb force about the pivot O of the wall-switch toggle. F = 0.32 18 A Answer: Mo= 15° 40° 0.770" lb-in.
Find the magnitude and direction of the resultant force for the given forces F, = 18 kN, F2 = 12 kN and F3 = 21 kN acting on hook fixed to a wall as shown in figure. Take e, = 39° & e2 = 39°. F1 F3 F2 (NOTE: ENTER ONLY THE VALUES BY REFERRING TO THE UNITS GIVEN IN THE BRACKET. ALSO, SUBMIT THE HANDWRITTEN ANSWER SHEET IN THE LINK PROVIDED) The sum of horizontal force component for the given system (unit is in kN), E =
Consider the frame shown in (figure 1). Suppose that F1=4.5kN. Determine the x and y components of the force that the pin at B exerts on the frame using scalar notation. Determine the x and y components of the force that the pin at A exerts on the frame using scalar notation.
Question #1: The radius of the two pulleys shown below is 1-ft. Other dimensions are as shown. Show that the moment due to the 50 lb tension in the rope is 355 ft-lb at any point in the system. 30°- B. 3 ft 50 lb 50 lb -30° 4 ft A 3 ft 2 ft
Q1: Determine the moments about point ( A ) due to the forces applied on the cantilevered beam. 4 kN 30° 30° 2 m 6 kN 2 m -- 2 m
Compute the magnitude of the moment Mo of the 375-lb force about the axis 0-0. Assume F = 375 lb, d = 14 in., H = 10.6 in., h = 5.6 in., 0 = 32°, and = 69°. F d H Answer: Mo i Ib-in.