steel:210000 E (MPa) copper:100000 E (MPa) L4 (cm)= 280 L5 (cm)= 255 P1(kN)= 220 P2(kN)= 76 In Figure 1, with its dimensions, loading status and material properties, different full circle cross-section rod has been given. The AB part of the rod is steel, 100 mm in diameter; BC part is copper and its diameter It is 80 mm. (a) Draw the normal force diagram of the bar. (b) Calculate the normal stresses to occur in parts AB and BC. (c) Calculate the total length change of the rod.

Q: thickness

A: Given  G=5600ksi with dia of 2 inches Aluminium alloy G = 4000ksi Torque = 10ft

Q: n the figure shown, the cutaway view shows a solid aluminum alloy of L= 600mm, A= 707mm^2 and E=…

A:

Q: The A-36 steel plate has a thickness of 12 mm. If there are shoulder fillets at B and C, and allow =…

A: Given A36 steelt=12mmσallow=150MPa

Q: Determine the total elongation of the bar shown in figure below. Materials E (GPa) Bronze 83…

A:

Q: Problem 2 Determine the total elongation of the bar shown in figure below. Materials E (GPa) Bronze…

A: Answer: The total elongation of the bar : ∆Ltotal = ( -7.517 × 10-5 × P ) mm  where, P is in…

Q: 1- Calculate the axial deformation of point C and D? (D=36mm) t. 1A 2M steel E=200G pa Bras E= 105…

A: Given: Esteel=200 GPaEBrass=105 GPaD=36 mm

Q: luminum 6061 T4, and a ss section areas of 1 in^2. laced on each of the bars AISI 4130 Steel

A: AISI 4130 steelAluminum 6061 T4Ti-6AAL-4VArea=1in2Axial-Stress=15ksi To-Find:- The bar will be more…

Q: Determine the total elongation of the bar shown in figure below. Materials E (GPa) Bronze 83…

A:

Q: A machine part is shown in Figure. The load varies from 2000 to 200 lb. (yield strength of Sy = 30…

A:

Q: Coefficient of Thermal Expansion Steel Rod (figure) a. Change in length if the rod is heated to…

A:

Q: For the rigid bar shows, find stresses in steel and aluminium. rods due to rise in temperature. of…

A: Since the deformation is greater than the existing gap, thus the net deformation is,

Q: EXERCISE 5 CC BY NC ND TA= 45 kN.m 200 mm dAB = 20mm Figure shows a composite rod structure…

A:

Q: Figure 1 shows a composite shaft ABCD acted upon horizontal forces. The

A:

Q: 8. 10 plate 8X10 - S00 pounds of loud material 6061 Aluminum - Determine what type of stress Is…

A: Hf

Q: a left wing carrying single propeller engine with a mass, m= 2P00 kg. The wing has a length, L =…

A:

Q: A 10 ft long steel member with pinned ends (i.e., pinned-pinned) is used as a column. The member…

A: From question, Length of steel shaft, L = 10ft=10×12 inch= 120 inch Thickness of member…

Q: A rectangular plate of width b-40 mm and thickness s 20 mm has a hole with a diameter d=8 mm in the…

A: Given:b=40 mms=20 mmd=8 mmF=15000 NFor dw=840=0.2;From the graph:Kf=2.5Stress developed without…

Q: A flat bar with a hole (see figure) has widths b = 60 mm and c = 40 mm. The fillets have radii equal…

A: b = 60 mm c = 40 mm R = 5 mm to determine diameter dmax of the largest hole

Q: cylindrical pressure vessel has inside diameter d_{o} = 500 mm and inside diameter di=490 mm.if it i…

A: Given Data Outside diameter of vessel is: do=500 mm Inside diameter iof vessel is:di=490 mm Factor…

Q: For the figure below determine the * following : R, NB, Ay,Ax R kN/m 300 mm -500 mm-

A: A pin support will exert both horizontal and vertical components of reaction. The support A is pin…

Q: Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution…

A:

Q: In the figure below, A 50 mm shaft is subjected to a reversed load P = + 2700 N. Find the length…

A: As per Bartleby's policy in case of multiple questions I can solve only first one. Please repost…

Q: Click to see additional instructions Calculate the minimum Safety Factor if the radius r= 5mm and M=…

A:

Q: Q2: Figure (2) shows a rotating shaft, simply supported at bearings at A and B. The shaft is loaded…

A: Given DataP=2669NT=282.462N.mSn=241.317MPad=25.4mmSu=551.581MPa

Q: Note: J3 = J2 G3 = G2 36 mm 0.99x10° mm* (1) 4 kN-m 70 GPa (2) 32 mm (3) 1.65x10 mm“ B 1000 mm C 20…

A:

Q: Calculate the compression resistance in kN of the cross-section of a stocky universal beam (UB)…

A:

Q: A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape…

A:

Q: HW 1// For the assembly shown in Figure 1. Find: a) Change in temperature so that the two bar just…

A: For steelE=210GPAA=250mm^2For aluminumE=70GPaA=650mm^2

Q: b) A composite bar is shown in figure Qlb. Determine. The thermal stresses in copper tube and steel…

A: As we know that due to temperature rise there must be increase in length according to its…

Q: 8. Refer to the figure below. Even though the cyclic loading accidentally caused the stresses to…

A:

Q: A rotating shaft of 25-mm diameter is simply supported by bearing reaction forces R₁ and R₂ The…

A:

Q: The solid 37 mm diameter steel [E - 200 GPa] shaft supports two belt pulleys. Assume that the…

A: Area of moment of inertia is property of object shape which help in finding the deflection of beam…

Q: The A-36 steel bolt is tightened within a hole so that the reactive torque on the shank AB can be…

A:

Q: i) Absolute maximum shear stress in AB Ans (TAB)mar 28.64 GPa 400 mm ii) Absolute maximum shear…

A:

Q: 3. A cylindrical rod is fixed between two walls. The rod is composed of two materials. Section AC is…

A:

Q: QUESTION 3: Square profile made of hollow 1045 steel, with a length of 6 meters with a…

A: Given data: Cross-section of Square hollow profile of steel pipe is drawn below. Cross-sectional…

Q: Please solve this question carefully and circle the final answer with the correct units use the…

A: Given that ,  D=30 mm E =73.1GPa Triangular distributed axial load .

Q: A pushrod in the valve mechanism of an automotive engine has a nominal length of 203 mm. If the rod…

A:

Q: d 5 in 150 mm 3 in W 2 in 40 mm 1.25 in F 600 lbf 2 kN 250 lbf M Ste Ste C

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.