A uniform bar AB weighing 500 kg is supported at both end by a cable as shown in the figure. Determine the smallest diameter in steel cable if the stress is not to exceed 120 MPa. ... Steel L=4m Bronze L=4m 10 m A 2.3 mm B 7.2 mm 5.1 mm 1.6 mm

A uniform bar AB weighing 500 kg is supported at both end by a cable as shown in the figure. Determine the smallest diameter in steel cable if the stress is not to exceed 120 MPa. ... Steel L=4m Bronze L=4m 10 m A 2.3 mm B 7.2 mm 5.1 mm 1.6 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An axial pull is acting on a bar consisting of two different materials is shown in figure.If the Young’s Modulus of M.S steel and Copper is 2 x 105 N/mm2 and 121 GPa respectively. Determine (i) Stress induced in each section, and; (ii) Total extension of the bar
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure below. Axial loads are applied at the positions indicated. If P = 4,500 lbs and the cross sectional area of the rod is 0.85 in?, determine the stress in each section. Steel Bronze 4P Aluminum P 2 ft 3 ft 2.5 ft
A horizontal load P is applied to an assembly consisting of two inclined bars, as shown in the figure. The cross-sectional area of bar (1) is 1.30 in.2, and the cross-sectional area of bar (2) is 1.75 in.2. The normal stress in either bar may not exceed 24 ksi. Determine the maximum load P that may be applied to this assembly. Assume dimensions of a=14.5 ft, b=9.0 ft, and c=14.5 ft. Determine the allowable force F1 in member (1) and the allowable force F2 in member (2).
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. The diameter of aluminum rod (1) is 2.50 in., the diameter of brass rod (2) is 1.75 in., and the diameter of steel rod (3) is 3.00 in. Determine the axial normal stress in each of the three rods. Assume P = 5 kips, Q = 3 kips, R = 13 kips and 5 = 24 kips. The normal stress is positive if tensile and negative if compressive. σ₁ = Answers: 0₂ = (1) 03 = (2) i i A Q B C D ksi ksi ksi
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 8 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 8 mm in diameter. Assume a = 530 mm, b = 265 mm, h = 390 mm, and 0= 70°. If the normal stress in tie rod (1) cannot exceed 180 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load Pmax that can be supported by the structure. D (1) a P i Answer: Pmax B b KN
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 11 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 8 mm in diameter. Assume a = 530 mm, b = 265 mm, h = 380 mm, and 8= 65°. If the normal stress in tie rod (1) cannot exceed 190 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load Pmax that can be supported by the structure. D Answer: Pmax= (1) i B b C /9 KN h P
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure below. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 200 MPa, in aluminum of 115 MPa, or in bronze of 145 MPa. Aluminum A = 400 mm2 Bronze A = 200 mm2 Steel A = 500 mm² P 2P 4P 2.5 m 2.0 m 1.5 m
2. Determine the largest weight W that can be supported by the two wires AB and AC as shown in Figure below. The working stresses are 100 MPa for AB and 150 MPa for AC. The cross-sectional areas of AB and AC are 400 mm? and 200 mm? respectively. B. 30° A 45° W
Determine the maximum axial force that can be applied to the bar shown in Figure 3. The allowable stress is 100 MPa. The dimensions are: Hole diameter 20 mm. Thickness of bar: 6 mm D = 40 mm d%3D20mm Fillet radius, r = 4 mm 40mm 20 mm r 4 mm 20 mm Figure 3 P.
The yoke and rod connection assembly shown in the figure below is subjected to a tensile force of 5 kN. I Determine the tensile stress in each rod. Determine the shear stress in pin A between the members. If each rod is 600 mm long, determine the overall extension of the assembly. Ignore any stretch in the joint. 40 mm 5 kN. 30 mm 25 mm 5 kN
Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is supported by double- shear pin connections at B and D. The pin at bracket A is a single-shear connection. The pin at B is 8 mm in diameter. Assume a = 600 mm, b = 300 mm, h = 330 mm, and 0= 70°. If the normal stress in tie rod (1) cannot exceed 190 MPa and the shear stress in pin B cannot exceed 100 MPa, determine the maximum load Pmax that can be supported by the structure. D Answer: Pmax= i B kN h