An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure below. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 200 MPa, in aluminum of 115 MPa, or in bronze of 145 MPа. Aluminum Bronze A = 400 mm? Steel A = 200 mm? A 500 mm2 P 2P 4P 2.5 m 2.0 m 1.5 m

An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure below. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 200 MPa, in aluminum of 115 MPa, or in bronze of 145 MPа. Aluminum Bronze A = 400 mm? Steel A = 200 mm? A 500 mm2 P 2P 4P 2.5 m 2.0 m 1.5 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

hot air is compressed polytropically so that the quantity pvn is constant. if 0.02m3 of air at atmospheric pressure and 4oc are compressed to a gage pressure of 405kn/m2, determine the final temperature (t2 in si)
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure below. Axial loads are applied at the positions indicated. If P = 4,500 lbs and the cross sectional area of the rod is 0.85 in?, determine the stress in each section. Steel Bronze 4P Aluminum P 2 ft 3 ft 2.5 ft
n the figure below, a member is subjected to an axial force P. If the cross sectional area of the member is denoted as AB, then the maximum value of its normal stress occurs when: ∅ = 00 ∅ = 300 ∅ = 450 ∅ =900
The figure below are cables ( circular section) supporting a 48 kN. Find the axial stress of each. The cables has a limited working stress of 79 mPa. What will be the required diameter of each cables to support the 48 kN load? MN kN = 48 kN
F2 Q1) Axial displacement of point C in the system shown on the left is 0.01 cm. Find the maximum elongation of the bar and the maximum normal stress. A F1 A. GIVEN: F2 = 100 kN, (1 = 240 cm, €2= 160 cm, bi = 5 cm, bz=10 cm, h=5 cm, E=2.107 N/em², a=20 cm Note: neglect stress concentration. h bị b2 A-A section
A steel bar, the material of which is S355 J2 G3, binds two walls together. Pre-tensioning in tie bar 4.3 kN. The temperature of the rod increases by 15 °C. Calculate the normal stress in the cross section of the bar. L = 600 mm, α = 12μ 1/°C, E = 200 GPa and d = 25 mm . Give the answer in MPa as a whole number as a numerical value only. Correct answer to exercise should be = -27
HW: 1-1-12 Find the axial stress in rods AB and BC. AB has a diameter of 25 mm and BC has a diameter of 15 mm. State if they are in tension (T) or compression (C). Answer(s): B A 6000N 8000N
Problem 3 The steel rod shown in the figure is stress- free before the axial loads P1 = 150 kN and P2 = 90 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial stress in each segment after the loads are applied. Use E = 200 GPa A A = 900 mm² 500 mm A = 2000 mm² B P₂ A = 1200 mm² с -250 mm 350 mm D
Two cylindrical copper alloy bars have the same length L, but different shapes, as can be seen in the figure. The two bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5 m, d = 80 mm, E = 110 GPa, and ν = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Two round solid bars of different materials are connected in series against rigid supports as shown in Figure 4. Determine the stress in each bar and the support reactions if temperature is increased by 18° C. Bar A da, EA, A Bar B dв, Ев, ав LA LB Figure 4 Use the following information. Bar, B: Length, LB Diameter, dB Poisson's Ratio Young's Modulus EB = 210 kN/mm2 Coefficient of expansion aB = 12.4x106 °C- Bar, A: Length, LA Diameter, dA = 25mm =D40 mm = 10 mm 30 mm S. = 0.28 =D0.32 = 70 kN/mm² Coefficient of expansion aa = 16.5x10-6 °C-I Poisson's Ratio %3D Young's Modulus EA
Last 2 digits 71 P N