Barra 1 Barra 2 d 2d

Q: The pin-connectsed structure consists of a rigid bar ABCD and two bronze alloy [E = 100 GPa] bares,…

A: GivenE=100GPaA=340mm2L1=810mmL2=1080mma=480mmb=38mmc=600mmσlim=165MPa

Q: Q-10 An aluminum alloy [E = 70 GPa; v=0.33; a = 23.0 x 10-6 /°C] plate is subjected to a tensile…

A: Given data Youngus modulus E= 70GPa = 70*103 Poissions ratio = 0.3 Coefficient of linear expansion…

Q: Compound axial member ABC shown in Figure Q-9 has a uniform diameter d = 37.5 mm. Q-9 Segment (1) is…

A: Write the expression of the area of the cross-section of the rod. Write the expression of Hooke’s…

Q: n the figure shown, the cutaway view shows a solid aluminum alloy of L= 600mm, A= 707mm^2 and E=…

A:

Q: A torsional moment T = 6,467 Nm and a load P = 87,599 N are applied at the same time to a circular…

A: This question is related to the torsion of the shaft. torsional shear stress or Torsional stress is…

Q: The figure shows a cantilever of length L = 4 m consisting of steel angles size of 100 x 100 x 12 mm…

A:

Q: s shown in the figure, two aluminum rods AB and BC, hinged to rigid supports, are pinned together at…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Q3/ A truss shown in Figure below is made of Aluminium and it consists of two rods. The…

A:

Q: least factor of safety if the material is cold-d

A: Sfhh

Q: What is the minimum required diameter of the rod if the factor of safety for tension failure is F.S.…

A: Given,load, P = 11 kN = 11,000 NFailure stress, σ= 60 Mpa = 60 N/mm2Factor of safety, FS =…

Q: Calculate the total deformation of steelbars shown in Figure. (d1=1A mm, d2=2A mm and E=210 GPa)…

A: Given, A=5B=3C=8d1=1A mm=1×5 mm=5 mm=5×10-3 md2=2A mm=2×5 mm=10 mm=10×10-3 m E=210 GPa=210×109 Pa…

Q: 2.2-11 A hollow, circular, steel column (E = 30,000 ksi) is subjected to a compressive load P, as…

A: Given figure,

Q: Tutorial Question on Axially Loaded Members Question One A steel bar 2.4 m long has a circular cross…

A: Approach to solving the question: using the formula for elongation of stress region and the…

Q: Consider the bar in Figure 2, which has cross-sectional area A = 1-10-3 m², modulus of elasticity…

A:

Q: A thin metal alloy plate is loaded by biaxial stress (2 directions) given by 8000 psi in the x…

A:

Q: 5. An angle bracket ABC is restrained by a high- strength steel wire CD, and it supports a load P at…

A:

Q: Problem: A horizontal steel wire AB is stretched between rigid supports. The initial pre-stress in…

A: Given data: σ=48 MPaTi=15°Cα=12×10-6 /°CE=200 GPa Need to determine the temperature when the stress…

Q: 3) The rigid horizontal bar AB is supported by three vertical rods as shown in the figure and…

A:

Q: A steel bar of thickness h, to be used as a beam, is welded to a vertical support by two fillet…

A: The allowable force, F, on the weld is approximately 252.84 kN.Explanation:Step 1: To find the…

Q: a.) An anchor rod with a circular head supports a load  Pallow = 15 kN by bearing on the surface of…

A: (A)The given load (P) = 15 kNHole diameter (h) = 2.6 cmFOS (n) = 1.6Ultimate tensile stress = 60 MPa

Q: A circular bar of magnesium alloy is 750mm long. The stress-strain diagram for the material is shown…

A: Here at firstCalculating the total strain at point B by using the following relationεB=δLlHere εB ia…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.