A closed thin walled cylindrical vessel has a diameter D of 660 mm, a wall thickness t of 2.0 mm and length L of 800 mm. It is subject to an internal pressure P of {P} MPa causing circumferential strain Eg of 0.009. Assuming that Youngs modulus is 200 GN/m² and Poisson's ratio is 0.3, calculate the internal pressure P. Give your answer in MPa to 3 significant figures. 4 P D

A closed thin walled cylindrical vessel has a diameter D of 660 mm, a wall thickness t of 2.0 mm and length L of 800 mm. It is subject to an internal pressure P of {P} MPa causing circumferential strain Eg of 0.009. Assuming that Youngs modulus is 200 GN/m² and Poisson's ratio is 0.3, calculate the internal pressure P. Give your answer in MPa to 3 significant figures. 4 P D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION 18 Rearrange the following steps which illustrate the sand-casting process in brief. Heat treatment of casting product is sometimes required to improve metallurgical properties Pour the molten metal into sand mold Cavity Break up the mold to remove casting A Allow time for metal to solidify + Clean and inspect casting product Make the Pattern and Core box * Separate gating and riser system + Prepare sand casting mold for pouring QUESTION 19 Which of the following is mostly used for holding bored part of the job? Mandrels Steadies Collet Face plate
this cylinder has a rod inside, around the rod there is paraffin wax that will expand, I want to know how to reduce the thickness of this cylinder. However, I don't know what formulas I need to be able to do this and how to do the calculations. Please can you make an example with the data you choose to have an example of how to do this step by step? Thank you Also keep in mind that the wax is expanding by an induction coil, and the heat is happening around the cylinder. And the thickness of the stainless steel cylinder has to be thin but not so thin that it causes a pressure problem.
8)
The below product in Figure Q1 requires to be sand casted based on the dimensions given. The past records revealed that a cylinder with a diameter of 1.5m with a height of 3m solidifies in 3 minutes in a sand casting operation using a similar material. a) Calculate the process time required for this design below. b) Suggest a suitable design of the riser. Specify what would be the riser dimension be in order to cater for this design. Justify your answer for the minimum possible size. c) Sketch a cross sectional drawing of the casting process with proper labeling of all the critical parts and suggest how would you modify the casting process if the cylinder part below required to be hollow instead of fully solid. r= 8 cm h = 60 cm 24 cm h = 220 cm Figure Ql
hello, where did you get the values from the first equation in step 2? and also, what formula did you use for this? thank you :)
Q2:-Choose the Correct answer. (1):- Grain growth in size (recrystallization) occurs at a- Hot-forming process b- Cold-forming process c- Warm- forming process (2):- The (Vent) is a small opening in the mold to facilitate escape of a- Air and Gases b- Metal e- Sand d-Water (3):- In the Tube Drawing Process, Dies are made of a- Hard Steel b- Copper e- Aluminum d- Wood (4):- The channel through which the molten metal enters the mold cavity called a a- Gate b- Runner e- Riser d- Chaplets (5):- In pressure Die-casting molten metal forced to cavity under a- High pressure b- Low pressure c- Medium pressure d- No pressure (6):- In Electric-Arc Furnaces charge is melted by heat generated from a- Electric are High power b- Electric are Low power e- Laser d- Charcoal (7):- The Hot-chamber die-casting it is limited to use with a- High-melting point metals b- low-melting point metals e- Both
could you plz take a photo of the solution, the solution above isn't clear, the words are all put together so i can't quite get it.
13. Are surface-hardened parts always case-hardened by carburizing?
Why is your Reynold's number 1400 instead of 2300?
For each question, provide an explanation, identifying the correct choice ( it is marked in red) and explaining why it's the right answer, as well as why the other options are incorrect. Please do all three
How do you draw a Sankey Diagram?