Draw Mohr’s circle that describes each of the following states of stress for diagram a, b, c.

Q: 50 MPa 60 MPa 100 MPa α ให้ 70 MPa

A: Given -To Find-

Q: .

A: Find outA. Determine the shear stress component acting on the inclined plane AB. solve the problem…

Q: Draw Mohr's circle for the state of stress defined by 01 = 80 MPa, o2 = -20 MPa and t12= 40 MPa. (1…

A: To draw mohr's circle for the state of stress

Q: 5. Determine the normal stress and shear stress acting on the inclined plane AB. Soive the problem…

A:

Q: Determine stress in rod

A: Given data :   Length (L)=5 mArea (A)=100 mm2Force (F)=10 KN

Q: -7. Determine the stress components acting on the 9-7. inclined plane AB. Solve the problem using…

A:

Q: The state of stress at the point can also be represented in termsof the maximum in-plane shear…

A: False, The state of stress at the point cannot be represented in terms of the maximum in-plane shear…

Q: Determine the orientation that causes normal stress to be a maximum?

A: Understand that the normal stress is maximum at the major principal plane. Therefore, to determine…

Q: The cross-sectional area of bar ABCD is 500 mm?. Determine the stress in segment BC. 40 kN 35 kN 20…

A:

Q: 6kN and 1.0kNm loads are applied to the top of the 62-mm-diameter cast-iron as shown. Determine the…

A:

Q: 4 ksi The state of plane stress at a point is shown on the element. (a) Draw Mohr's circle neatly to…

A:

Q: (e) E = бу 30 MPa Txy 85 MPa Ox 120 MPa = =

A: GivenPart eσx=-120MPaσy=30MPaτxy=85Mpa part fσx=30MPaσy=-80MPaτxy=15Mpa

Q: Q4: The forces F1 and F2 act on a bracket as shown in the Figure below. Determine the magnitude of…

A:

Q: The internal drag truss for the wing of a light airplane is subjected to the forces shown. Determine…

A:

Q: of 3.0 mm is produced at the tom of the groove. Compute the maximum stress in the rod y axial…

A:

Q: Draw and stress tensonr with the following characteristics The stress cube visualization at point…

A:

Q: A steel pipe 120 mm external diameter and 60 mm internal diameter is subjected to an internal…

A:

Q: 1. For the given state of stress, determine (a) the principal planes, (b) the principal stresses.

A:

Q: For the given state of stress, determine the planes with compressive normal stress equal to 15 MPa.…

A:

Q: 5 mm B. ON A 1900 N 800 M

A: given:

Q: Determine the diameter of the bolts if the stress in bolt 1 is 200Mpa. Note: Distances are in mm.

A: The information provided in the image, it is not possible to directly determine the diameter of the…

Q: A cantilevered solid shaft with length of 400-mm and diameter of 150-mm is loaded at its free end as…

A:

Q: 2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless…

A: Given data: The allowable stress in the cable is, σa=5.2 ksi. The weight of the cylinder is, w=890…

Q: If each grid in Mohrs circle below is 15 MPa then the maximum principal stress is: 1 grid square =…

A: It is the very basic question of mechanics of material portion. Used concept is nomenclature of…

Q: Solve using Mohr's circle

A: For the given state of stress, To find: The normal and shearing stresses after the element has…

Q: - The state of plane stress at a point is shown on the element in Figure below. Represent this state…

A:

Q: Determine the maximum stress at the fillet of the filleted flat plate of 8 mm thickness as shown in…

A:

Q: A.) If the F = { - 200i + 400j } N , determine the force in each member and state if its in…

A:

Q: The distribution of stress in an isotropic aluminium machine component is given (in MPa) as: σ₂ = y…

A:

Q: The state of stress at a point in a member is shown on the element below. If: 0x = 9 MPa Oy=-14 MPa…

A:

Q: Problem 3-2. For the following section, determine the stresses at points A, B, C, D E and F. Given:…

A: The moment applied is

Q: The bell-crank mechanism shown in the figure is in equilibrium. Determine (1) the normal stress in…

A: Given:Diameter of the pin at B, d=8 mmThickness of the bracket, tb=6 mmThickness of the crank, tc=10…

Q: 9-15. Determine the equivalent state of stress on an element at the same point oriented 30°…

A:

Q: In the figure shown below, set P = 48 lb, D1 = 8 in, D2 = 4 in, D3 = 4 in, and the bit diameter to…

A:

Q: How is the state of plane stress at the point uniquely represented?

A: If the stress state at a material particle is such that the only non-zero stress components act in…

Q: Required information Consider the given state of stress. Take X= 16 MPa and Y= 48 MPa. Y

A: GivenX=16MPaY=48MPa

Q: Calculate the values of ol and o3 in the rock if the differential stress is 40 MPa and the center is…

A: differential stress = 40 MPa. (diameter of the Mohr's circle).Therefore, the radius of the Mohr's…

Q: *8-36. The drill is jammed in the wall and is subjected to the torque and force shown. Determine the…

A: The free body diagram of the system is as follows.

Q: Consider the given state of stress. Given: X= 6 ksi and Y= 30 ksi. + 6 ksi The normal stress is…

A:

Q: Problem 3: The rod below has a diamter of 2 in. Determine the state of stress at point A, and show…

A: The diameter of rod is

Q: Problem 2: A state of plane stress at a point on the surface of a structure consists of the…

A: Givenσx=18ksiσy=24ksiτxy=15ksi

Q: In each case, the state of stress sx, sy, txy produces normal and shear stress components along…

A: (a) sx'=-5 kPasy'=0τx'y'=8 kPau=20°   The stress along the normal -axis:…