A tensile test is peformed on a brass specimen 10 mm in diameter using a gage length of 50 mm (see figure). When the tensile load P reaches a value of 20 kN, the distance between the gage marks has increased by 0.122 mm. (a) What is the modulus of elasticity E of the brass? (b) If the diameter decreases by 0.00830mm, what is Poisson's ratio? 10 mm - 50 mm

A tensile test is peformed on a brass specimen 10 mm in diameter using a gage length of 50 mm (see figure). When the tensile load P reaches a value of 20 kN, the distance between the gage marks has increased by 0.122 mm. (a) What is the modulus of elasticity E of the brass? (b) If the diameter decreases by 0.00830mm, what is Poisson's ratio? 10 mm - 50 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Manufacturing methods
Q3 Give the reason for 10 of the following. - 1- The use of lubricant in wire drawing die. 2- The uses of tungsten carbide for the manufacturing of die tool. 3- The increase of Mo/Si ratio during the production of white cast iron. 4- The addition of Al to copper alloys. 5- Aluminum is a better overall conductor than Copper for long distance electric transformation. 6- The addition of cryolite in smelting electrical furnace due to the production of aluminum. 7- The addition of Magnesium and Cerium during the production of Ductile cast iron. 8- The addition of 13% Cr to steel in corrosive environment. 9- The increase of hardness for chips due to the cutting process. 10- The brittle fracture of steel at low temperature lower than -4 C. 11- The heating of metal after the rolling process.
What is meant by Thicket and thinned? What is the difference in between both types? Note: Please do not handwritten and write short answer.
Properties of areas of common shapes. INCLUDE ALL THE REFERENCE (LINKS)
The rope you are uncoiling is a right hand lay rope, state with reasons the direction of uncoiling.
Q.B3. As part of a project, students have been asked to cast an Aluminium disc for use as a flywheel. The flywheel is part of an engine development project and needs to be 200 mm in diameter and 20 mm thick. Green sand casting will be used. The shrinkage associated with this metal and process is 5% at the solidification stage and further 3 % on cooling to room temperature. Aluminum has a density of 2710 kg/m³ and a melting temperature of 660°C. The pouring temperature is 700°C while the specific heat of aluminum is 887 J/kg.K. The latent heat of fusion of Aluminum is 396 kJ/kg. From previous experiments the Chorinov constant for the mold was found to be 10 s/mm². Determine: a.) The dimensions of the pattern (diameter and thickness) that will need to be made for this part (ignore riser and sprue). b.) The time it will take for complete solidification of the part. c.) Assuming an electric furnace at 10% efficiency is used to heat the metal and it takes around 2 hours achieve pouring…
5)
Increasing the degree of graphite nodularity produces an improvement in cast iron elongation, due to ........... .........
Q1) One way of shaping raw materials into useful and valuable products is through casting process. Casting technology or process is one of the oldest processes in manufacturing field. During the last century, this casting process is used to create gold, jewellery and other products. (i) Draw TWO (2) casting processes that would be most suitable for making a gold and jewellery. (ii) Discuss your answer in (i) (iii) Explain why sand-casting process is not suitable for making a gold and jewellery.
Give an example of Dilatation?