An aluminum rod is rigidly fastened between a bronze rod and a steel rod as shown in the figure. Axial loads are applied at the positions indicated. Determine the deformation of each rod under given load. The modulus of elasticity is: Eg =100 GPa, EA =80 GPa and E, =150 GPa Use the last TWO digits of your ID Number for the missing force PN

Q: 1-) b. 1+j 1 Evaluate a. 1+j

A: Ans(a)  j2=-1 Divide by 1-j both sides 1-j1+j×1-j1-j (1-j)21-j2=1+j2-2j2=-2j2=-j

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Write the mathematical expression for the Brinell hardness test. HB=2PπDD-D2-d2 Here, Applied load…

Q: In the crank-slider shown, OA = 5 cm, AB = 15 cm and the offset e = 7 cm. Find the value of angle a…

A:

Q: The figure shows the chain drive of a bicycle. How far will the bicycle move if the pedals are…

A:

Q: Figure 1. Length of line AC? Zradis 8.33" 10 5.83" 9.72" 11.33" Figure 1. Value of angle <BAC in…

A:

Q: Which percentile is typically for designing lower-limit dimensions? - 95th 5th 50th 99th

A:

Q: 10) in the following figure, if h2-10" and h1=5", then, the angle of taper equal 10" Ⓒa. 60⁰ Hand…

A: These are small blocks of alloy steel. Used in the manufacturing shops as length standards. Not to…

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: Consider a virtual load Q, acting vertically downwards, is applied at point A.Draw the given truss…

Q: Problem 1: a) Draw the free body diagram of the member ABC? b) Determine the reaction forces at the…

A:

Q: What is the value of w and y? y W 6V2

A:

Q: Question The figure below shows a hollow circular beam with an outside diameter of 250 mm and a wall…

A:

Q: If A=0.375 inch, B=0.923 inch, C=1.0992 inches, find G A 기사 W -|×|-> G- -B- -C- F E-

A: If A= 0.375 inch, B=0.923 inch, C=1.0992 inches,find G.

Q: Find the volume described by 0srs 5,0seS T/3, Os O S 2M O a. 125T/3 O b. 251T/3 Oc. 225T/3 Od.…

A: Answer: The volume is 125π/3 . Option (a) is correct.

Q: Question 18 Simplify (−4 − 4j) O 1.412-45° O 1.41/225° O 1.414-225° O 1.41/45°

A: Simply the above expression

Q: 76°10' 0.500 DIA 45°00'- 1.125 DIA 1.000 0.875 Find length x in the accompanying figure.

A: Given figure can be redrawn as:

Q: A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 180 KN,…

A: Given : The shear force in this section is The diagram is,

Q: Determine ly and ky.

A:

Q: 19. Find the resultant and angle of the figure shown below. 1120 N

A:

Q: Given: Diameter of pipe in point 1 = 3.2 Diameter of pipe in point 2 = 2.3 Specific gravity of the…

A: since the units of pressure are not provided, assuming the unit to be ft of water Velocity at…

Q: 150 m 50 mm 85 mm Section X-X 20 kN

A:

Q: The steel wide-flange beam has the dimensions shown. If it is made of an elastic perfectly plastic…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: Determine the magnitude of F so that the resultant couple moment is 11.5 kN -m , counterclockwise.…

A:

Q: Question 3) On the  plate in the figure, the length  L  is given as L=72 m . According to this;…

A:

Q: G R.75 00.63 THRU 01.123 F0.250 1.00 chamfer with distance 0.25 mm fillet with radius 0.25 mm fillet…

A: Select the correct statement about the notation circled in green and marked as letter F. Assume all…

Q: What is the distance between the points labeled A and B? Start a new drawing based on…

A: According to the given data Thickness of the wall=100mm We need to find Distance b/w A and B

Q: Build the following part. Report the volume in mm^3. Assume all dimensions are in mm. A=52 B=19 Your…

A: Given : To find : Volume of the body

Q: Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please

A:

Q: Draw the orthographic Projections of given object.

A: Orthographic projections are projections of a component in three directions that are perpendicular…

Q: What is the location of FR, i.e., the distance d? A M 3 m 3 m F. R B

A:

Q: Question 3) The length L is given as L=34 m on the plate in the figure. According to this; Question…

A:

Q: Choose the false statement Mark only one oval. Thermometers work on the basis of zeroth law Some…

A: Adiabatic system are also called isolated system this is incorrect statement

Q: is find mo B) The angle btween ã=i+jtk ち-mi-k

A:

Numerical Calculations

In the mid-20th century, the availability and the growth in power of digital computers led to the increase in the mathematical model in the field of engineering and science. The analysis of these detailed models needs to be increased.