--マ火ル-M12INA =50x50312INA = 520833-33mm4(a) The aixal stres n Shecoss-sectionwe Knos thatJa = 20x1o325008MPAThis is theaxial - stressen he Cross-section x -X 50 mm150 mm50 mm85 mmSection X-X20 kN

Answered: Image /qna-images/answer/7b7f1d8b-d550-4f34-a9ab-2d2345bdb142.jpg

Answered: 150 m 50 mm 85 mm Section X-X 20 kN

Engineering

Mechanical Engineering

150 m 50 mm 85 mm Section X-X 20 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

FIND THE FOLLOWING SHAPE WEIGHT CENTER BY REFERENCES O point.(The center of the small circle coincides with the vertex of the rectangle.)(''b'' is the diameter of the small circle)(c=a+(b/2)(b diameter small circle, semicircle, rectangle and triangle large removed from the rectangle.) a=44mm b=10mm
answer this ; The vertical coordinate (y-coordinate; the y-axis serves as the axis of symmetry of the cross-section.) and horizontal coordinate (z-coordinate) of the location where the maximum shear stress occurs in the section are y= mm ; z= mm; The vertical distance from the location where the maximum shear stress occurs in the section to the bottom side ( AB ) of the cross section can be calculated as Distance = mm
This shoulder bolt is composed of hot-rolled monel. The head of the shoulder bolt is a regular hexagon and it measures 6 mm across opposite flats. The other dimensions of the bolt are given below, as well as the forces to which this component is subjected. Find the change in length of each segment of the part as well as the overall change in length from A to D F_A = 4.8 kN F_B = 5.1 kN F_C =1.6 kN F_D = 1.9 kN a = 4mm b = 4.1 cm c = 6.8 cm d_s = 5 mm d_t (effective) = 3mm Assume:∙ Bearing stress between threads of the bolt and the nut may be neglected∙ Stress concentration effects may be neglected∙ The force that the nut applies may be treated as a concentrated force.∙ The nut may be treated as rigid.∙ The forces applied to the nut and the shoulders of the bolt are distributed evenly around their perimeters δAB = δBC = δCD = δoverall =
A 60 mm diameter shaft AB is rigidly attached to the beam CDFH of 30 mm by 40 mm rectangular cross-section as shown in Figure Q4. The beam is pin supported at C and H. A torque of 2 kN.m (moment about z axis) is applied to end B of the shaft. Determine: (a) the reactions at supports Cand H, (b) the rotation about z axis of end B of the shaft by using Castigliano's second theorem, (c) the slope (rotation about z axis) at point C of the beam by using Castigliano's second theorem. The shaft and the beam are made of an aluminum alloy for which E = 72 GPa and G=27 GPa. Assume that the hub DF is rigid and neglect the strain energy due to transverse shear.
A left hand threaded 14 mm diameter A36 steel bolt is stuck in a metal block. Assume the bolt head is flush with the block surface at A. In order to remove the bolt the 50 Nm torque is applied to the bolt head as shown. The block applies a resisting torque "t" to the stuck threads which is assumed to be uniformly distributed along the 50 mm buried depth. G = 75 GPa a) Explain the difference between right and left hand threaded bolts Determine: b) The magnitude of the uniform resisting torque "t" (including proper units) c) The internal torque as a function of x measured from B (a FBD is required) d) The maximum shear stress in the bolt Ans: 92.8 MPa e) The angle of twist of bolt head A with respect to end B Ans: 0.0044 rad f) The largest torque that can be applied to the bolt head before it twists off (Tyield = 150 MPa) %3D
A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 281 KN, determine the value and the location of the maximum shear stress in the section. In Figure Q2, a = 72 mm and the origin of the coordinate system is at centroid of the cross section. Z A a AY 2a O 4a Figure Q2 J.L B 3a a
Parvinbhai
Need help with all 4 questions please include all units and steps. Thanks
One shaft is in torsion as shown below. If the magnitude of shear stress at point A is 345.6 MPa, calculate the magnitude of the shear stress at point B on the same cross-section as point A: MPa. Calculate your answer to 1 decimal place. 40 mm 30 mm T
Use Mohr's Circle to determine the maximum shear stress on the element, also using Mohr's Circle determine the maximum normal stress on the element.