A turbine shaft transmits 500 kW power at 900 rpm. The permissible shear stress is 80N/mm² while twist is limited to 0.5º in a length of 2.5 m. Take G = 0.8x10⁵ N/mm², on thebasis of torsional rigidity; i.Determine diameter of shaft if solid shaft is used. ii.If hollow shaft is chosen with di/do = 0.6, determine the suitable diameters of theshaf

Q: A motor driving a solid circular steel shaft transmits 85 horsepower to a gear at point B (see…

A:

Q: The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and…

A:

Q: A hollow aluminum propeller shaft, 30 ft. Ilong with 15 in. outer diameter and an inner diameter…

A: (a) The maximum shear stress, τmax = 3.8 ksi. (b) The angle of twist of the shaft, θmax = 0.052…

Q: A hollow bronze shaft (G=5000ksi) has an outer diameter of 3in and a wall thickness of 0.25in. The…

A: Given data: Converting all data into SI units. Modulus of rigidity G=5000 ksi=34473.8 Mpa Outer…

Q: 4 mm module 20° full-depth The gear shown above is to transmit 1 kW at a speed of 200 rev/min. Find…

A:

Q: A hollow shaft of diameter ratio 3/5 is required to transmit 400 kW at 140 r.p.m with a uniform…

A: Given that ; Power P=400kW=400×103WSpeedN=140 rpmshear…

Q: 3.10 The stepped steel shaft carries the torque T. Determine the maximum allow- able magnitude of T…

A:

Q: Problem #1. The 20-mm diameter shaft is subjected to torques as shown. The shaft is made of steel…

A: For solution refer below images

Q: solid shaft is transmitting 9 KW at 550 r.p.m. Determine the diameter of the shaft if the maximum…

A: for solution refer below images.

Q: A tubular steel shaft transmits a power of P = 450 hp at a speed of 3000 rpm. Determine the maximum…

A:

Q: Torsion A hollow circular shaft has inside and outside diameters of 30 mm and 40 mm respectively.…

A:

Q: n outside diameter of 70 m and :

A: here outer dia (70m) is >>>> inner dia (50mm). so the polar moment of inertia almost…

Q: A solid steel shaft must not twist through more than 30 in a 6-m length when ted to a torque of 12…

A: Given Twist angle = 30 Length =  6m Torque = 12 kNm Modulus of rigidity = 83 GPa To find Smallest…

Q: A 1.30-in.-diameter solid shaft is subjected to an axial force of P = 2000 lb, a horizontal shear…

A: Solution:

Q: Consider a solid circular shaft A-D with varied diameter (dAB=0.6 in, d³c-0.75 in, and dcp=0.9 in).…

A: In conclusionFinding the exact location of maximum shear stress and plotting the shear stress…

Q: 2 A hollow simple supported shaft 3m made of steel with di/do of 0.6. The shaft is subjected to a…

A:

Q: what is the Moment at point A

A: First find the moment produce by given torque as follows.

Q: For the circular shaft (G=12×106 psi) shown below: a. Compute the reaction torque and draw the…

A: According to the given data Segment  Diameter(in) Hollow diameter(in) Length(in) G(psi AB 6 4…

Q: The maximum angle of twist on a 2.5 ft solid SAE1020 Cold drawn  steel shaft can not exceed 0.35…

A:

Q: A shaft supported at the ends carries a spur gear and is to transmit 10 kW at 200 rpm. The weight of…

A: Consider a shaft of diameter d and length L is subjected to a torque T. Then, torsional shear stress…

Q: Problem #1. The 20-mm diameter shaft is subjected to torques as shown. The shaft is made of steel…

A:

Q: Bearing stress 5. Please provide proper discussion and illustration also complete solution and…

A: given; transmitting force(F)=50KN                                     =50*103Nshear stress on…

Q: A hollow aluminum propeller shaft, 30 ft. long with 15 in. outer diameter and an inner diameter…

A: GIVEN DATA-

Q: Missing value MT = M0 (kN.m) 170 Kindly write legibly. Thank you Solve for: a) Determine the shear…

A:

Q: A hollow shaft with a length of 1103mm and outer diameter 73mm and inner diameter 50mm is required…

A:

Q: shaft made of steel receives 7.5 kW power at 1500 r.p.m. A pulley mounted on the shaft as shown Fig.…

A:

Q: J.A hollow shaft is 50 mm outside diameter and 30 mm internal diameter. An applied torque of 1.5 Nm…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: A hollow shaft made from AISI 4340 steel has an outer diameter Do of 4 in. and an inne diameter Di…

A:

Q: An engine develops 5.0 MW at 115 RPM and the ratio of maximum to mean torques is 1.3 to 1. Calculate…

A:

Q: A hollow circular shaft transmits 25 horsepower while operating at a rate of 180 rev/min. If the…

A:

Q: A shaft in torsion only is to transmit 2500 HP at 570 rpm with mild shock. Its material is AISI 1137…

A:

Q: 1. A shaft is made from AISI 1040 hot rolled steel with Su = 496 MPa, Sy = 290 MPa with 18%…

A:

Q: Find the diameter of a shaft to transmit twisting moments varying from 800 N-m to 1600 N-m. The…

A:

Q: A solid steel shaft is subjected to torsional loadings. If T=10 kN-m. T= 45 MPa, the diameter of the…

A:

Q: A steel shaft ABCD having a total length of 3.5 m consists of three lengths having different…

A: Torque is the rotational equivalent of linear force. It is also referred to as the moment, moment of…

Q: Problem 10.2. A stepped steel shaft with diameters d, = 56 mm and d = 52 mm is twisted by torques T1…

A: d1 = 56 mm d2 = 52 mm T1 = 2.5 kN.m T2 = 1.5 kN.m

Q: A solid 1.6 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant.…

A:

Q: QUESTION 2: 2.1 A shaft is to transmit 190 kW at 180 rev/min. If the maximum torque transmitted is…

A:

Q: A drive shaft is made of solid steel. It is desired to transmit 2.5 hp at 150 rpm. The allowable…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.