A drive shaft is made of solid steel. It is desired to transmit2.5 hp at 150 rpm. The allowable shear stress in Tallow = 27ksi. What is the minimum required diameter of the tube tothe nearest 1/8 in.The required diameter is D280isoBY NC SA2021 Cathy ZupkeСсx in.

Answered: Image /qna-images/answer/7c43c536-bad1-4570-ab60-7ed9a674bce9.jpg

Answered: A drive shaft is made of solid steel.…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A gear drive is required to transmit a maximum power of 22.5KW, the velocity ratio is 1:2 and the rpm of the pinion is 200 .the approximate center distance between the shaft may be taken as 600mm.the teeth has 20°stub involute profile.the static stress for the gear material ( which is cast iron ) may be taken as 60MPa and face width as 10 times the module.find the module, face width and number of teeth on each gear.Check the design for dynamic and wear loads. The deformation factor in the buckling equation may be taken as 80 and material combination factor for the wear as 1.4
A solid shaft made from AISI 1040 cold-drawn steel is used to carry two V-belt, as shown in the Fig. 3. Pulley A receives power from a motor through a belt, with the belt tensions shown in Fig. 3. The power is transmitted through the shaft and delivered to the belt through pulley B. Assume the belt tension on the loose side is 10 percent of the tension on the tight side.
(8) An axle (non-rotating) is to be machined from AISI 1144, OQT 1,000°F, to the proportions keyway в shown, with a fillet radius r = 0.2D; F varies 1.SD from 400 lb. to 1,200 lb.; the supports are to the left of B, not shown. Let N = 2 (Soderberg Line). 6" (a) At the fillet, compute D and the 30 maximum tensile stress. (b) Compute D at section B. (c) Specify suitable dimensions. Keeping the given proportions, would a smaller diameter be permissible if the fillet were shot-peened?

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A drive shaft is made of solid steel. It is desired to transmit 2.5 hp at 150 rpm. The allowable shear stress in Tallow = 27 ksi. What is the minimum required diameter of the tube to the nearest 1/8 in. The required diameter is D 280 iso BY NC SA 2021 Cathy Zupke Сс x in.