A steel shaft ABCD having a total length of 3.5 m consists of three lengths having different sections as follows: AB is hollow having outside and inside diameters of 100 mm and 62.5 mm respectively, and BC and CD are solid. BC has a diameter of 100 mm and CD has a diameter of 87.5 mm. If the angle of twist is the same for each section, Calculate the length of each section, I1, lz and l3. Analyse the value of the applied torque and the total angle of twist, if the maximum shear stress in the hollow portion is PP MPa and shear modulus, G=QQ GPa. PP=75MPA Please refer appendix for PP and QQ values. QQ=88GPA B D 62.5 mm 100 mm 100 mm 87.5 mm 3.5 m

A steel shaft ABCD having a total length of 3.5 m consists of three lengths having different sections as follows: AB is hollow having outside and inside diameters of 100 mm and 62.5 mm respectively, and BC and CD are solid. BC has a diameter of 100 mm and CD has a diameter of 87.5 mm. If the angle of twist is the same for each section, Calculate the length of each section, I1, lz and l3. Analyse the value of the applied torque and the total angle of twist, if the maximum shear stress in the hollow portion is PP MPa and shear modulus, G=QQ GPa. PP=75MPA Please refer appendix for PP and QQ values. QQ=88GPA B D 62.5 mm 100 mm 100 mm 87.5 mm 3.5 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate angle of twist of B with respect of A in rad
Homework help
A circular shaft of the dimensions shown in the following figure is subjected to three torques : T1 = 28 k-in, T2 = -8 k-in and T3 = 10 k-in. (a) What is the angle of twist of the right end due to the applied torque? (b) Plot the angle of twist diagram along the shaft. Let, G= 12×106 psi.
The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
A metal shaft ABCD with variable cross-section is subjected to three external torques (T₁=28 kip- in, T2=8 kip-in, and T3=10 kip-in) as shown in the figure below. Each torque is acting at the locations marked with circular points along the shaft. Note that a 16-inch long segment of the shaft at the free end (right) has a 1-inch diameter bore. The dimensions (lengths and diameters) of the shaft are given in the figure. Assume deformation is linear elastic and take G=12×106 psi. D [3" 16"- X C T₁ 2" -32"- T₂ 1" diam. bore B -16"- A T3 the bar has a uniform diameter d along its full length, but external torques remain the same and are applied at the same locations. If the failure shear stress for the material is equal to Tfail = 10 ksi, and the factor of safety is equal to 2, determine the required (uniform) diameter d for the bar. Assume that the bar is solid for its entire length.
Please I want answer of that question from these choices
Consider the solid steel shaft shown. Take T= 60 kip-in. 1.5 in. A ¹2 3 ft B K Problem 3.033.a - Determine angle of twist in a solid steel shaft Determine the angle of twist at A. Use G=11.2 x 106 psi. (Round the final answer to three decimal places.) The angle of twist at A is
A solid 0.64-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (1). 10 lb-ft 50 lb-ft 70 Ib-ft | (1) 30 lb-ft A (3) B D 3150 psi O 2524 psi 1876 psi O 2331 psi O 2932 psi
A hollow shaft with a length of 1103mm and outer diameter 73mm and inner diameter 50mm is required to tranmit a power of 60kW at a speed of 2950 rpm if the modulus of rigidity is 79.5GPa calculate the angle of twist in degrees
Formulate the equation of angle of twist at end C with respect to A in terms of T
Figure 1 is presented the solid shaft AB rotates at 650 rpm and transmits 30 kW from the motor machine tools connected to gears F and G. Assuming that, 10 kW is taken off at gear F and 20 k taken off at gear G, knowing that allowable torsional shear stress is equal to (65 plus last digit of student ID) MPa. Design the smallest permissible diameter of shaft AB. Figure 1 150 mm 225 mm 905 mm 150 mm 60 mm 100 mm D. 60 mm B.
PLEASE ANSWER NUMBER 3.11 MECH 221: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.