Problem #1. The 20-mm diameter shaft is subjected to torques as shown. The shaft is made of steel with the following properties: Elastic Modulus, E = 200 GPa and Shear Modulus, G = 75 GPa. Determine the following: (a) Absolute maximum torsional shear stress b) Angle of twist of the end B with respect to the support Show complete solution (FBDs and equilibrium equations).

Q: Suppose that P 9 kN and P2 = 14 kN. (Figure 1) Figure 1 of 1 30 2 m 2 m 2m

A:

Q: In (Figure 1), P₁ = 12 kN and P₂ = 6 kN. Figure 2 m G B 1 m 2 m 1 m 1 of 1

A:

Q: Determine the vertical displacement of point B. Each A-36 steel member has a cross- sectional area…

A: Given,A = 400 mm2E = 200 GPa

Q: A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape…

A:

Q: The assembly shown in the figure below consists of two sections of galvanized steel pipe connected…

A:

Q: Find the reactions at pins A, B, and C in the frame below if you REPLACE the 6 kips pointing down at…

A:

Q: For the element shown in the figure, replace the distributed load with the equivalent nodal forces.…

A: To replace the distributed load with equivalent nodal forces, we need to calculate the forces at…

Q: The truss is supported by a pin at A and a roller at B. (Figure 1) Figure y 10 kN 2 m- 4 m- X 2 m 5…

A:

Q: Please solve in Handwritten format with free body diagram. Don't use chatgpt.

A: Step 1:

Q: Example Problem: 4-31 (modified) The concrete column is reinforced using four steel reinforcing…

A: According to the given data d=18mm a=300mm P=800kN Est=200GPa Ec=25GPa We need to find Stress in the…

Q: A Ax = Bx = Ex = Number W Find the magnitude of the horizontal and vertical components of the pin…

A:

Q: A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape…

A:

Q: QUESTION 13 The compound steel bar shown in Figure is made of three uniform segments marked as 1, 2…

A:

Q: Find the reactions. Fill in the blank's. help me solve please

A:

Q: The truss is supported by a pin at A and a roller at B. (Figure 1) Figure y 5 kN 2 m 4 m 45° 10 kN…

A:

Q: diagram of member AC in Figure P4-2. 3' 3' A C 5' B 2 2

A:

Q: A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape…

A:

Q: i) Find the "x" and "y" components of the reaction force at A. Ax A₂ Ay = ii) Find the "x" and "y"…

A: According to the given dataConsidering the free body diagram AC and BCDE We need to find theReaction…

Q: Bracket BCD is supported by a hinge at C and a cable at B, as shown below. Given the forces P=288 N…

A:

Q: The overhang beam is supported by a pin at point A and a roller at point B. A distributed load is…

A:

Q: Please draw a FBD only for the circled yellow part known as a rubber base plate :) I don’t want the…

A:

Q: In the structure shown below (Figure 3), two forces of equal magnitude (P) are applied along the…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.