A three phase, Y-connected, 220 V, 50Hz, 6-pole, inductionhas the following parameters referred to stator in Q2/ph:motor,R1=0.294, R2 =0.144, X1=0.503, X2=0.209, and Xm = 13.15The total friction and windage losses are 200 watts.Draw per phase equivalent circuit and calculate the following at a slip of 2"a- Stator current?b- Power factor?c- Output power?d- Output torquee- Efficency??

Step 1: Given slip s= 2%=0.02Step 2:Step 3:Step 4: Remember power stage of induction motor to solve…

Answered: A three phase, Y-connected, 220 V,…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

Consider the following statements regarding the design of the distributed armature winding in a three-phasealternator:1. It reduces the phase belt harmonics.2. It increases utilization of armature iron and copper.3. It increases rigidity and mechanical strength of the winding.4. It reduces copper in the overhand of the winding. Which of the statements are correct? a. 1,3 and 4b. 2,3 and 4c. 1,2 and 3d. 1,2,3 and 4
Maz a) A sinewave is having a frequency of 50 Hz and instantaneous value of 250 Volts at 1.3 milli seconds. Find D The maximum value of sinusoidal voltage waveform and i) The value of voltage at 2.1 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 10 milli seconds and 0 =40 degrees. on Vp Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximnum value = a) (ii) Value of voltage at 2.1 ms = b) Angular frequency =
Describe the figures below and how each of figure below are working
Q choose the correct answer: 1-Brushless excitation system consisting of.... a- Stator field winding and power diodes b-stator and rotor field winding and capacitor c- stator and rotor field winding and capacitor d- Everything mentioned in the options 2- Voltage generated per phase in an alternator is proportional to a- Flux per pole b- Number of turns in armature c-Winding factors d- Everything mentioned in the options e- Frequency of waveform 3- If input mech. Power of SG constant, the functionality of AVR is a- Control flux of rotor b-Control terminal voltage c- Control flux and terminal voltage d-Control Load angle
A 220 V , 60 Hz , supply is connected to 200 – turn armature winding of reluctance 1.7x105 At / Wb . Find : 1-the magnetizing reactance. 2-the rms values of the ( magneto – motive force , exciting and armature currents , magnetic flux.) 3-the inductance. 4-Draw the phasor diagram of the circuit.
DEGREE: ELECTRICAL ENGINEERING SUBJECT/COURSE: AC MACHINES Answer the following questions (A, B and C) depending on the topic. 1. ALTERNATORS A. Why is it necessary to maintain the speed of an alternator at all times and how do they control the speed of an alternator when in operation? B. Distinguish between half-coiled and full-coiled armature windings in alternators. C. Why are fractional pitch windings generally used in alternators?
For the design we assuming following parameters 1) winding : Lap 2) simplex 3) Number of slots : 16 , single turn coil with 2 conductors per slot 4) Number of poles = 4
Needed to be solve In 20 minutes please
Untitled Section Jalis 6 In d.c. generators armature reaction is produced by field current O armature current commutating winding current none of the mentioned compensating winding current *.The use of d.c. generators eliminated the use of rectifiers and ac supplies True False O
A 110 V, 60 Hz, 6 – pole single phase induction motor 1/3 hp has the following equivalent circuit impedances: RI = 1.52 ohm, R2 = 3.13 ohm and x1 =2.10 ohm, x2 =1.56 ohm. Xm=58.2 ohm, The Friction, windage and stry losses =16W, the core loss = 35 W, For a slip of 0.05, calculation (a) input current, (b) power factor, (c) developed power, (d) output power, (e) speed (f) in put power (g) air gab power (h) T ind (i) T load 6) efficiency.
A DC series generator is supplying a current of 5A to a series lighting system through a feeder ofto total resistance, 1.0 ohm. The terminal voltage is 2500 V. The armature and series fieldresistances are respectively 18 and 15 ohms respectively. A 30-ohm diverter resistance isshunted across the series field. Determine the power developed in the armature of thegenerator?
Two shunt generators are connected in parallel to supply a current of 1500A. Each machine has a field resistance of 60 ohms and an armature resistance of 0.01 ohm. The generated emf by each machine are 455V and 460V, respectively. Calculate the power delivered by each machine.

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS