A tensile load of 50 kN is acting on rod of 50 mm diameter and length of 5 m. Determine the length of a bore of 25 mm that can be made central in the rod, if the total extension is not to exceed by 25 percent under the same tensile load Take E= 205 x 10' N/mm?. A 5m S0IN SOKN (a ) ROD WITHOUT BORE 5000 mm 50KN A 50KN F(5000-LB) (b) ROD WITH BORE

Q: A compound shaft consisting of a steel segment and an aluminum segment is acted upon by two torques…

A:

Q: Determine the force P to move block B. SHOW COMPLETE SOLUTION AND ILLUSTRATION FINAL ANSWER IN 3…

A:

Q: Problem 6.2. The undeformed and deformed outline of a material element are as shown in the figure…

A: Consider the given figure 1.} Calculate γxy at corners A,B,C and D Shear strain γxy is given by…

Q: The force of F = 55 lb acts along the edge DB of the tetrahedron shown in (Figure 1). Figure 8 ft 10…

A:

Q: The beam is acted upon by force F = 16 KN as shown in the figure. 50 mm F E1.5 m 3 m 100 mm -1= 19.3…

A:

Q: Q2: - A tape 100m long. it's cross sectional area in 0.0585 cm, the apparent length of which was…

A: Length L = 1500 m = 150000 cm Area A = 0.0585 cm2 Standardised pull Ps = 6.75 kg Actual Pull P =…

Q: The blocks shown in the figure weighs 35 kips. Find the value of x

A: Thw weight of the block is balanced by buoyant force by oil and water.

Q: 100 90 80 70 60 50 40 30 20 10 0.5 0.05 Grain size (mm)-log scale From the graph D60 = 0.997 mm; D30…

A:

Q: y 53 mm 85 mm 25 mm 57° 25 mm - b 65 mm

A:

Q: A ring is formed by rotating the area 360° about the x̄ – x̄ axes. Determine its volume.

A: Volume = area*length

Q: y 2 m 2 m 2 m 2 m 4 m 4 m Figure 1. Determine Xg and Yg

A: To Determine Centroid of the given figure. Xg and Yg

Q: A flat steel bar, 26 mm wide by 3 mm thick and 1.3 m long, is bent by couples applied at the ends so…

A: First task  To calculate Radius of curvature using central deflection given in the question.…

Q: Required: Vertical displacement at C PL AE E MB = 0 Fal (6m) – 50kN (2.5m) =0 Fa = 20.83kN %3D Steel…

A:

Q: A flat bar 10 mm thick and 100 mm wide is subjected to a pull of 100 kN. One side of the bar is…

A:

Q: PROBLEM 8: Locate the center of mass of the block in millimeters. Materials 1, 2 and 3 have…

A:

Q: 4m B 3m 28 KN/m 6m D 4m

A:

Q: 2) Reqd: Determine 0 of A relative to D Gst = 12 x 106 psi MN lb • ft 2-in. diameter 1000 lb · ft…

A: J =πd432=π×2432=1.57 in4

Q: What

A:

Q: a Find the distance x between the points (1,4) and (5, –8).

A: Distance X between two points is calculated as follow

Q: Question 3 An 4.3 meter aluminum square wire is hanging vertically. A tensile load of 350 KN is…

A: As per bartleby policy i can do only one question at a time. Please upload again other questions.…

Q: A tape 100m long, it's cross sectional area in 0.0585 cm', the apparent length of which was found to…

A: Given that:                     Nominal length of tape, l = 100mArea of cross section, A = 0.0585…

Q: An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure.…

A: stresses on an element is given as followschange in length of diagonal BD=?

Q: The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

A: Given : To Find :

Q: Problem 3 Figure a 1 1.5 in. + 1 in.] 0.5 in. 0.5 in. 3 in.3 in. ▼ Part A If a = 9 in., locate the…

A:

Q: What will be max. height that the water tank that may become full if the max. tangential stress is…

A:

Q: 30 m 54 mm 48 mm 54 mm 72 mm A thin, homogeneous wire is bent to form the perimeter of the figure…

A: Wire is bent to form the perimeter of figure aboveCentre of gravity of wire with respect to x,y =?

Q: Compute the resultant using cosine law and the angle of the R measure CW from the x – axis.

A: Transform the given forces as shownin the figure:Angle…

Q: (Figure 1) Figure 30 mm 140 mm. 30 mm 30 mm 70 mm 30 mm 170 mm 1 of 1 > ▼ Part A Determine the…

A: to find the centroid of the area about its left edge and the moment of inertia about its vertical…

Q: Q3: - Use nodal analysis to find the value of Vab 4₁ = 40 mA R₁ = 20 2 ww R₂ h 300. 60 mA V3=0 R3 =…

A:

Q: 3.A hydraulic press works according to the following scheme: Calculate the value of the load W that…

A: Given that:                        Area of large piston, A = 150cm2Area of small piston, a =…

Q: Question 1 啊 [B][025]. determine the reaction force at node 2 Given 31 1m 2 kNm 4(2) Reaction force…

A:

Q: What will be max. height that the water tank that may become full if the max. tangential stress is…

A:

Q: PROBLEM 1 For the area shown, do the following: a. Determine the centroid with respect to the…

A: Note: As per bartleby guidelines, only 1st 3 subparts need to be solved. For rest of the parts…

Q: Q1) Three bars each made of different materials are connected together and placed between two walls…

A:

Q: A rectangular bar is subjected to tensile forces of 2230 kN. Use E = 110 GPa and v = 0.34. Determine…

A: This question is related to the Strength of Material.

Q: I was wondering in the hydrodynamics how i can determine Cp in the pressure ressistance (coefficient…

A: In the context of total resistance, the coefficient of drag (Cd) is a dimensionless quantity that…

Beams and Frames

A beam is a horizontal structure or a member which is always subjected to transverse shear loads.