Ʈallow (MPa)=95     Ø(rad)=0.015     a (mm)=80    d (mm)=40

Q: Compute the coordinates of the centroid (7,5) of the area shown. Also compute the area moment of…

A: Given: a=14 mm b =113 mm c=18 mm d =49 mm h=99 mm w=14 mm Required: x and y coordinate of centroid…

Q: Bar ABC has an outer diameter of 10 mm and is made of red brass for which E = 100 GPa. Section AB is…

A: Consider the BC portion of the beam:

Q: Im still confused since we didn't end up with the same final values as the photo. Its showing TA =…

A: Given problem related to "calculation regarding torque".

Q: B A B' A piece of thin, uniform sheet metal is cut to form the machine component shown. Denoting the…

A:

Q: Build the following part. Report the volume in mm^3. Assume all dimensions are in mm.

A: Volume of 1=(40×17×38) - Volume of 2                          =(40×17×38) - 12×10×10×17…

Q: y y = a√bx C- CC x BY NC SA 2016 Eric Davishahl Values for dimensions on the figure are given in the…

A:

Q: Problem 6: A rectangular plate ABCD undergoes deformation to form a parallelogram AB'C'D'. The…

A: From the diagram, I conclude that options (D) (E) are correct statements. I didn't give solution…

Q: R W Problem Statement: The cantilevered round bar in the figure with diameter d = 25 mm, is made…

A: Given:-      Fx=Fy=0                   Fz=1400N          diameter of rod d=25 mm           a=500 mm,…

Q: Compute the coordinates of the centroid (7,5) of the area shown. лу a b 3 с d h W kd- b mm. ko*…

A:

Q: 30 m 54 mm 48 mm 54 mm 72 mm A thin, homogeneous wire is bent to form the perimeter of the figure…

A: Wire is bent to form the perimeter of figure aboveCentre of gravity of wire with respect to x,y =?

Q: Q3: - Use nodal analysis to find the value of Vab 4₁ = 40 mA R₁ = 20 2 ww R₂ h 300. 60 mA V3=0 R3 =…

A:

Q: QUESTION 2 The sides of a closed figure have been measured and found to have a total lenght of…

A:

Q: The area of the cross section of an airplane wing has the following properties about the and y axes…

A: Ix=450 in4Iy=1730 in4Ixy=138 in4To determine- Mohr circle

Q: e centroid (7, g) of the area shown. passes through the centroid.

A: Given:- a = 32 mm b = 13 mm c = 16 mm d = 57 mm

Q: HI= BM+BS RL SNO BS IS FS HI RL 1.115 0:745 7245 1-065 O'785 1.315 2150 845 325-675 150 326-825…

A: student must write data as given below since the BS are the reading which are done from already…

Q: Locate the centroid y of the cross section. Express your answer to three significant figures and…

A: Find out - 1) Centroid about Y axis .2) Moment of Inertia about the x' axis.

Q: 28.30mm 28.20mm чомра 6-A 20mm by 20mm square is etched onto a metal bar prior to loading. Upon…

A: To find Poisson ratio and Young's modulus

Coordinate Geometry of Survey

Coordinate geometry (COGO) is a method of inserting surveying or engineering data into geographic information system (GIS), computer-aided design (CAD), or mapping software. These data can be collected on the proposed construction site using standard surveying techniques and instrumentation or may be taken from existing maps, engineering plans, drawings, or records. Data gathered on the site includes coordinates of points, bearings, and distances between points. The data are noticed and noted through conventional surveying procedures, like a traverse or layout measurement series and it can be either digital or non-digital. The maps and plans are inclusive of boundaries, divisions, and other components, and these features are shown with coordinate values, the lengths, offset distance, and bearings between them.