QUESTION 2 The sides of a closed figure have been measured and found to have a total lenght of 4921.82. If the total error in the measurements is estimated to be equal to 0.25, what is the precision of the work. State only the denominator value and do not use any decimals.

Q: Determine the x-component (m) of the centroid of the given figure if the cut portion is a semicircle…

A: Given data,  a = 34 m b = 18 m c = 2 m Radius of Semi-circle = 8 m To find out the centroid of X…

Q: What is the area of the below figure if you know x=32.7? (use Simpson's rule) 32 33 28 30 X X- X-…

A: X=32.7

Q: Im still confused since we didn't end up with the same final values as the photo. Its showing TA =…

A: Given problem related to "calculation regarding torque".

Q: 20. Determine the location of the centroid of the figure shown above measured from the y-axis. Use x…

A:

Q: The answer in the book is a=1.67 m

A: From the given question, we have to find out the value of 'a' to consider the same amount of…

Q: Problem 1B. Use Newton's Method to interpolate the value of f(2.8). 1.6 2.5 3.2 4 4.5 f(x) 8. 14 15…

A:

Q: Determine the location of the centroid of the figure shown above measured from the y-axis. Use x =…

A: solution Find the area of each figure A1=4.354.74=20.619sq units A2=124.352×2.59=11.2665sq units…

Q: Determine the maximum deflection of the beam. Assume that a wooden beam has a vertical deflection…

A: Ans is given below

Q: Determine the moment of inertia about the x-axis of the shaded area shown. |1.la y= 1.la coS 2a

A: The given figure is shown below:

Q: Interpolate between In (4) = 1.386294361 and In (8) = 2.079441542. Also, compute the percent…

A: Given  Ln(4) =1.386294361  Ln(8) = 2.079441542

Q: Deflection Given: the beam cross-section shown have the following cross-sectional properties  f'c…

A: Gross moment of inertia(Ig)Critical internal moment(Mcr)Maximum service load(Ma)Critical moment of…

Q: 1. Determine the external reactions at the roller and pin supporting the above beam. 2. Determine…

A:

Q: Use Virtual Work Method to answer the questions below considering the truss shown. Use the…

A: Truss : Truss is a structure in which number of members are connected to each other and forms a…

Q: The 16 x 22 x 25-mm rubber blocks shown are used in a double U shear mount to isolate the vibration…

A:

Q: Estimate the error in evaluating the function f(x) = e2x* sin x %3D near the point x = 1.369, if the…

A:

Q: What is the area of the below figure if you (know x=31.7? (use Simpson's rule 33 27 32 28 30 31

A: Given information  Ordinates  Distance between Ordinates  To find area using simpsons

Q: Given the reference system, determines a coordinate of the centroid Ycg of the symmetrical plane…

A:

Q: The vertical stress increment (Aơ) due to a point load acting on the surface of linearly elastic…

A: In solid mechanics, the linear dependability investigation of a versatile arrangement is…

Q: For the element shown below, radius of Mohr circle is? Ox dy oy 0x o₂=110 N/mm², o, 30 N/mm² and…

A: Given- State of stress- σx=110 N/mm2,σy=30 N/mm2,τxy=30 N/mm2, It is needed to find the radius of…

Q: What is the area of the below figure if you know x=35.7? (use Simpson's rule) 33 27 32 28 30 31

A:

Q: Classify each of the structures as statically determinate, indeterminate or unstable. If…

A: Diagram (d) and (e) are provided. We have to find out determinacy/Indeterminacy and stability of the…

Q: Question 2, Write the boundary conditions and show how you would drive the frequency equation for…

A:

Q: A tapered circular varying from 20 mm to 10 mm is

A:

Q: (X)f 7-8 = (r)f %3D t – x = (x)f = (1)/ Hind a formula for a rational fundtion that has a vertical…

A:

Q: What is the area of the below figure if you know x=32.2? (use Simpson's rule) 33 27 30 32 28 31

A: Given- X=32.2

Q: 1. A line is recorded as Am long. It is measured with a (E÷200)kg tape (Bm full tape length) which…

A: Surveying: It is an art of determining the relative position of points on above or below the surface…

Q: Determine the x-component (mm) of the centroid of the plane figure if a=69, b=123 and c=165. Round…

A: To find x component of centroid

Q: Resolve F2 into components along the u and v axes, and determine the magnitudes of these components.…

A: The angles in the triangle can be found by the concept of alternate angles triangle(angle 30 degree)…

Q: Find: . X centroid with respect to coordinate system shown (mm).

A:

Q: What is the area of the below figure if you know d=30? (use trapezoidal rule) A 32 26 28 24 p. p.

A: To determine: The area of the given figure using trapezoidal rule.

Q: You first say that RA=57.1667. Then later in the problem you use the value 157.1667...what is the…

A:

Q: determine the deflection at E in mm using Double Integration Method Consider 150 mm x 150 mm section…

A:

Dependence on mechanical properties

The mechanical properties of materials are those structures that include the reaction to the load used. Metal switching features determine the scope of the usefulness of the content and establish the expected service life. Machine structures are also used to help distinguish and identify material objects. The most common mechanical properties considered are strength, ductility, stiffness, impact resistance, and resilience to fractures.