3. (a) Determine centroid of the shaded area of the following figure. (b) Determine the volume V of the solid generated by revolving the shaded area through 270 degrees about the x-axis. 75 mm 75 mm 60 mm 60 mm 60 mm 75 mm

Q: A load of 7400 N acts on the machine part shown in Fig. 5a. The machine part has a uniform thickness…

A:

Q: Suppose that F=560 N. (Figure 1) Figure 4 m 30° 12 13 A 6 m x Part A Determine the magnitude of the…

A:

Q: Given the following, pick the correct shear diagram for this beam from below. ● ● ● D1₁ = 10 ft D₂ =…

A:

Q: Problem 3: For a sandstone reservoir, calculate the water saturation if the porosity (Ø) is (20 %),…

A:

Q: If a 200 N force F1 is applied to the piston with the 4 cm diameter, what is the magnitude of the…

A:

Q: Figure P3.58 1.89 emp 3.59 Water is siphoned from a tank as shown in Fig. P3.59. Deter- mine the…

A:

Q: 1. Express the two forces shown as Cartesian vectors. 2. Determine the magnitude and coordinate…

A: Given:- The magnitude of the force along with AB = FAB = 200 N  The magnitude of the force along…

Q: Can you help me figure out the different symbols and how many of them are there and put them in…

A: Single Pole Switch Duplex Outlet Quadruplex Outlet Electrical Outlet Fan Outlet Wall Mounted…

Q: Please show all steps and units.   Thank you

A: Given data:- The given diameter of the pipe, D=200  mm The given minor loss, K=0.3 The given…

Q: HAnd written and clean writing please Solve all parts

A:

Q: Prob. 2 For the given loading, determine the zero-force members in the truss shown.

A: To Determine For the given truss, which of the following members are carrying zero force / no force.…

Q: 1- Given Data Ꭰ L 40 in × 30 in fy Column = 350 Kips = 250 Kips = 60 ksi fé fy qa Footing = 3.25 ksi…

A: Data provided -column                                  Footing                                1Ksf…

Q: Area of the Triangles are denoted by the following formulas: 1. Basic Formula, A = 12 * base*…

A: Given: From the figure, AC=1690.54 m

Q: 1. For the following list, provide an appropriate definition along with the APA reference for each.…

A:

Q: The pipe ACDE is supported by ball-and-socket joints at A and E and by the wire DF. Determine the…

A:

Q: The boring logs for the new site of the FEB indicates that there is a 16 ft thick layer of silt,…

A:

Q: 4a. Draw the quantitative (i.e. including values) influence line for the vertical reaction at E. A 4…

A: To determine ILD for reaction at EILD for an internal moment at CILD for shear just to the left of…

Q: 4. The driver of a vehicle on a level road determined that she could increase her speed from rest to…

A: Speed increased from rest to 50 mph in 34.8 secSpeed increased from rest to 65 mph in 94.8…

Q: The automobile has a speed of 70 ft/s at point A and an acceleration aa having a magnitude of 20…

A:

Q: =\ Fill in the blanks with appropriate words. 1. The fracture planes oriented more or less ---- 2.…

A:

Q: 2. A column in a building is subjected to the following load effects: 9 kips compression from dead…

A: Dead Load (D) = 9 k)ips Roof live load (Lr) = 5 kips Snow load (S) = 6 kips Load due to rain…

Q: why does the field of engineering need standardization in technical drawing?

A: Standardization in technical drawings mean ensuring and fixing certain parameters in drawings to…

Q: Sec. 8.1-8.3 8-1. Determine the equations of the elastic curve for the beam using the x and x;…

A: The given data us: Load P acting at distance a from each support. EI = constant

Q: 3. Determine the support reactions on the member shown below. The collar at B is fixed to the member…

A: Given, external force of 100 lb To determine, support reactions

Q: The average normal stresses developed in section a - a of the turnbuckle, and the bolts shanks at B…

A: Given Data Cross sectional area at section a-a = 1in. × 0.25 in. Diameter of bolt shank (d) = 0.5…

Q: Calculate unknown force

A: This question is from solid mechanics

Q: Solve using the method of sections. Determine the force in members BC, CH, and GH of the 3 m truss…

A:

Q: A section of an OH line needs to be built on 46 ft. wood poles set 6 ft. deep in the ground. Each…

A: hag = Height of pole above ground = 46 - 6 = 40 fthbg = Height of pole below ground = 6 ft l1 =…

Q: Refer to the hydroelectric plant as shown in the figure. Determine the amount of power transferred…

A: GIVEN DATA:-⇒Diameter of pipe= 300mm  OR 0.3 m⇒Discharge (QB)= 1.7 m3/s⇒Frictional head loss= 4 m

Q: Determine (a) the shear strains at all corners and (b) average normal strain that occurs along…

A:

Q: Choose the correct one and explain it

A: Given data : Normal stress in X direction (σX)=5 MPaNormal stress in Y direction (σX)=5 MPaMajor…

Q: he elevation of BM 132 is known to be 153.236 m. The length of the level run was 780 1, with each…

A:

Q: 2. Given a rectangular plate which is deformed as shown by the broken line. Determine the average…

A:

Q: Graph I would like you to please write a drawing clearly so that I can transfer it to graph paper

A:

Q: F4-3. Determine the internal normal force, shear force, and bending moment acting at point Cin the…

A:

Q: I cannot read the equations in the answer. Is there a way to submit it in a different format?

A: Given: Flow between parallel plate with one of them moving with speed v  Required: Write the…

Q: Explain the terms acronym and abbreviation. Differentiate between the two by giving relevant…

A: acronym- It contains a set of initial letters from a phrase that usually form another word. In other…

Q: a good handwriting is important in the field of engineering?

A: The ability of a reader to understand the things readily while reading depends upon how good one…

Q: 5. A 400 lb force F is applied to lever-shaft assembly as shown. a) Determine the moment of the…

A:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.