Link AB is to be made of a steel for which the normal stress is 310 MPa. Determine the cross-sectional area (in mm2) for AB if P = 18.5 kNand d = 0.35. %3D %3D Round off the final aswer to four decimal places. 8 kN/m 35° OE D BỊ d d d

Q: 10-m-long steel rails of a railroad track (E,= 200 GPa and a = 117 x 10°C) were laid at a…

A: Using formula to find stress due to temperature rise

Q: Situation 01. A 60-kg block is at rest when an upward force parallel to the 15° surface is applied.…

A:

Q: A simply supported wood beam is reinforced with a steel plate of width b as shown in the figure. The…

A: Given data  Modular ration (m) = 20  b = 4 in. w = 252 lb/ft  L = 19.3 ft  B = 6 in  D = 10 in…

Q: Refer from the figure shown below: a.) What force F must be applied to the following static…

A:

Q: 1-The point of action of the result force is below the centroid, why?

A: Centroid is defined as the geometrical centre of object or body.

Q: Link BD consists of a single wooden member 37.5 mm wide and 21.3 mm thick. Knowing that each pin has…

A:

Q: The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the…

A:

Q: What is the thermometer reading at 1:09 P.M.?

A: This question is based on Newton's law of cooling

Q: If the allowable bearing stress for the material under the supports at A and B is Ob = 810 psi,…

A:

Q: ANSWER

A:

Q: Consider a solid shaft of 1.4-in. diameter. Determine the maximum shearing stress in the shaft as it…

A: Given data  Power (P) = 66 hp  N = 780 rpm  Diameter of solid shaft (d) = 1.4 in    Find maximum…

Q: W P'

A:

Q: Determine the required diameter (in inches) of rod ACif the allowable normal stress is 22.51 ksi and…

A:

Q: Locations where the V curve crosses the V = 0 axis are important because they indicate where the…

A: Concept used: Shear forceV= Slope of bending moment diagramdMdx V=dMdx

Q: Problem 1: A singly reinforced rectangular beam has a dimension b = 310mm and d = 410 mm. Factored…

A:

Q: Determine the largest weight W (in Ib) that can be supported safely by the structure shown in the…

A:

Q: 1O N A GN

A:

Q: 0.5 in. B 1.8 in. P - 0.5 in. A 60° 1.8 in. 45° C

A:

Q: The electric motor exerts a 500-N-m torque on the aluminum shaft ABCD when it is rotating at a…

A:

Q: A torque T-43 kip-in. is applied at end A of the composite shaft shown. Know that the modulus of…

A:

Q: The rigid bar BC is supported by the steel rod AC of cross-sectional area 0.28 in2. Find the…

A: Calculate vertical deflection of point c?

Q: A bucket is hanging from a horizontally moving crane. Calculate the maximum allowable speed (m/s) of…

A:

Q: If a horizontal force P = 12 lb is applied to block A, determine the acceleration of block A.…

A: g=9.81m/s2 = 32.185ft/s2  mA = 8/32.185 lb  mB = 15/32.185 lb

Q: The mechanism shown is used to lower handicapped persons into a whirlpool tub for therapeutic…

A:

Q: The New York City water supply system is one of the most extensive municipal water systems in the…

A: Solution: (d) Part Solution If average rainfall=25 in/yearThen Total Rainfall will beQ=25×7.90×109…

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 13 kN applied at A. Assume a…

A: F1=13 kNa=310 mmb=190 mmc=70 mmθ=40oDiameter of pin=23 mmThickness of bell crank=32 mm To find:-…

Q: in the system if the specific weight of the air is to be neglected. Suppose the temperature of the…

A:

Q: Calculate the Shear Force at point A of the following Beam. Take X=35 kN and Y=80KN YKN X kN/m A, D…

A: Given, Beam,

Q: For sand bed streams, incipient motion unstable if:

A: velocity 1.6 m/secparticle dia 3mmchannel width-8mchannel depth-0.2mchannel slope-0.001n=0.03

Q: A 2650-N-m torque 7 is applied to the hollow shaft as shown. NOTE: This is a multi-part question.…

A: Using formula to find maximum shear stress

Q: The compound shaft consists of bronze and steel segments, both having 125-mm diameters. If the…

A:

Q: a ga in tension with the following results: Applied 1 Strain Force (N) (mm) (%) 0 5.000 Stress (MPa)…

A: We…

Q: A hollow steel shaft, 5.8 ft long, has an outer diameter of 3.06 in. and an inner diameter of 1.28…

A: Given:Length of steel shaft, L=5.8 ftOuter diameter of shaft, do=3.06 ininner diameter of shaft,…

Q: Q.50 Uniaxial compression test data for a solid metal bar of length 1 m is shown in the figure.…

A:

Q: Profile Level Notes: The elevation of BM A = 533.00' BS (plus sight) on BM A = 6.91' IFS (minus…

A: To Determine :- Elevation of the STA 1+50 Concept :- HI = Elevation + BS Elevation = HI - IFS…

Q: The coefficient of static friction between the 199.44-kg crate and the flat bed of the truck is u =…

A:

Q: An equal-tangent vertical curve is to be constructed between grades of +3.0% and -0.5% (final). Due…

A: Answer  We are given Initial grade G1 = 3% Final grade G2 = -0.5% Offset at highest point in the…

Q: The aluminum shell is fully bonded to the brass core, and the assembly is unstressed at a…

A: Given Data:Temperature of 78°FChange in Temperature = 210°FBrass…

Q: Set up the appropriate equation that is used to solve for the moment of inertia about the y axis.…

A: