Determine the required diameter (in inches) of rod ACif the allowable normal stress is 22.51 ksi and P = 9.76 kips. Round off the final answer to four decimal places. 5 ft D |B -10 ft -10 ft-

Q: The picture of the graph isn't showing can you please resubmit it?

A: GIVEN: To Calculate: Draw the Graph of GRAIN size distribution curve.

Q: The following is the bearing and length measurements of an opentraverse A) Determine the latitude…

A: The latitude of the traverse line is extend on the north and south direction and departure of the…

Q: Convert the following distances given in feet to meters: Part A 521.80 sft Express your answer in…

A: convert the following distances given in ft to meters :-Part A)521.80 sftPart B)2100073.9 sftPart…

Q: One of the following choices is not among the types of volume counts : * Time variation counts.…

A: Volume count  Counting the number of vehicles passing through a point in a given interval of time ,…

Q: Note: Replace all zero digits of your ID number by number "2" Problem #4: A 8 = 10+C (degrees) В C…

A:

Q: A trip table (veh./hr) needs to be loaded on the network shown in the table below. Find the total…

A: Step 1:Step 2:

Q: QUESTION 1: ISOMETRIC Q1(a): Taking X as the lowest view point, sketch the isometric view of the…

A: Given details are- Top view , front view and side view The hand drawing of isometric view is…

Q: Please make your own question about horizontal distance (surverying) and solve it on your own. Make…

A:

Q: Break the shaded area into the five different areas shown. Find the area and the x- and…

A: Determine  a. Break the shades area into the five different area and find area, x and y coordinates…

Q: 7. PROFILE file of pro- level notes and show the customary arithmetic check. LEVELING. Complete the…

A: Given: The differential leveling notes are given below, STA BS HI FS IFS ELEV BM-0…

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: * aut cad Ray is one of the commands for the drawing list. It is used to draw a ray, using two…

A: Explanation :  Ray  command in AutoCAD  is used to draw rays from a starting point in a perticular…

Q: 4. V2+ v7n; if n = 7 5. (금);ifn=2

A: 4. 2+7n ; if n = 7 It is given that the value of n is 7. Therefore, 2+7n=2+7×7=2+49=2+7=9=3

Q: an object moving horizontally after t seconds is given by the it3 +36t2-54t, where s is measured in…

A:

Q: Solve ONLY LETTER D and E.  The first three subparts are already answered in my previous question.…

A:

Q: What is the length of the dividing line? (Type your answer using 2 decimal places, numerical value…

A:

Q: = 6x – 0.5x y(0) = 0 y(12)= 0 Finally, Find y (4)

A:

Q: 80 11 B 10 mm 10 mm 80 10 mm

A:

Q: d t (consta nt thicknes s) b Area (xbar) Ixo lyo ly NA 1- = 11 in 0.3 in 4 in 3.300 in2 1.495 in…

A:

Q: You are a professor of architecture. Show your students where the horizon line and vanishing points…

A:

Q: Lil Sample Problem 2 2. Calculate the velocity of water flowing in point 2? Water Open Tank

A: The depth of water in tank, h=3mThe tank is opoen to atmosphere.

Q: centroid C of the beam having the cross-sectional area shown 150 mm 150 mm 20 mm 20 mm B

A:

Q: Determine the coordinates of the centroid of the shaded area. y 15 E 30 35 15 40 50 30 --X 100…

A:

Q: The section comprising of two 250 x 37 channels shown was built-up in such a way that their…

A:

Q: earson MyLab and Mastering X roblem 9.19…

A:

Q: Untitled Section A distance between point (A) and (B) is (170m) was measured by a tape of (20m)…

A:

Q: Hand Writing not allowed please provide Typed answer

A: The distance between v1 and v2 is  √37 or approximately 6.08 units.Explanation:Formula for distance…

Q: A building measures 10m * 6m its to be placed on A4 sheet 1:50. Calculate the margin at the button…

A: Given ratio for plot = 1:50 Size of the plot = 10 m×6 m Size of sheet = 296 mm×210 mm (Landscape)

Q: PROBLEM 1: Determine Ix and Ix.

A: FInd…

Q: 6. Discuss the methods of determining permeability in the field. 7. Water flows under constant head…

A: Note- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: Please recheck and answer in 3 decimal places.

A:

Q: Two springs are used to support the steel truss structure of 2.5 m height shown in the figure. The…

A: Given: Spring 1: (right support) Shear modulus, G1=300+41=341 GPa Spring diameter, d1=20 mm Helical…

Q: The Howe roof truss shown in figure below carried the given loads. The wind loads are perpendicular…

A: A Howe truss is a type of truss bridge that consists of chords, verticals, and diagonals with…

Q: What are the geocentric coordinates in meters of a station which has a latitude of 50°25'33.71631"…

A: ϕA=Latitude of station=50°25'33.71631''NλA=Longitude of station=121°49'53.68672''WhA=Height of…

Q: Please make your own question about vertical distance (surverying) and solve it on your own. Make it…

A:

Q: From the solving the equation log x = 4 we have x equal 2 16 2ln4 O 2^. 4In2

A: Given: log2x=4 The above expression is to be solved for the value of x.

Q: LOCATE THE CENTRO IP 50mm Somm 150 mm MM 150mm 240mm 56mm ! 400mm

A:

Q: Convert 109° 46' 51" to degree decimals. Round your answer to 3 decimal places. Do not include units…

A: To convert in degree decimal