A plate with width of 500 millimeters and thickness of 25 millimeters is to be connected to a double plate of the same width and with a thickness of 10 mm each by a 36-millimeter-diameter bolts, as shown in the figure. The plates are all A36 steel with a yield strength of 250 MPa and an untimate tensile strength of 400 MPa. It is required to determine the value of "b" such that the net width along the bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. 60 mm 100 mm 100 mm P 500 mm 100 mm. PA 150 mm 1 3

A plate with width of 500 millimeters and thickness of 25 millimeters is to be connected to a double plate of the same width and with a thickness of 10 mm each by a 36-millimeter-diameter bolts, as shown in the figure. The plates are all A36 steel with a yield strength of 250 MPa and an untimate tensile strength of 400 MPa. It is required to determine the value of "b" such that the net width along the bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. 60 mm 100 mm 100 mm P 500 mm 100 mm. PA 150 mm 1 3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q.2) The assembly shown below is composed of an aluminum tube and a cylindrical steel plug. The mass density of aluminum and steel are 2700 kg/m³ and 7800 kg/m³, respectively. Find the coordinates of the mass center. y Tube A- Plug 20 mm 35 mm 100 100 A- mm mm Section A-A
Toblem 13.92 The bar is made of a 2014-T6 aluminum alloy. Take that L=9.6 ft (Figure 1) Figure 1 of 1 600 lb 605 Part A Determine its smallest thickness b if its width is 5b. Assume that it is fixed connected at its ends. Express your answer to three significant figures and include the appropriate units. μA b= Value Submit Units My Answers Give Up ?
Solve equations 1 and 2 shown below. All the values are given below please subsitute in the two equations and solve for P. The value of P must be in kips. Pls show all calculations along with units. Also solve for Wdl (I have put a question mark next to it under Given section), must be in PLF. thanks in advance will give a thumbs up and good rating. the same question was answered wrong last time, Sx was considered. u dont need Sx, Ma/ohm as a whole is 8.71k - ft. The value of P shouldnt be negative.Thats why use proper units
Solve the question below. Show your complete solution.
Locate the centroid y of the cross section. Express your answer to three significant figures and include the appropriate units. y = Submit Part B μA Ir = Value Request Answer Determine the moment of inertia of the section about the z' axis. Express your answer to three significant figures and include the appropriate units. μA Units Value BEL Units 378 ?
28.30mm 28.20mm 90MPa 6-A 20mm by 20mm square is etched onto a metal bar prior to loading. Upon loading, the dimensions of the etched shape become those indicated on the figure. Determine Young's modulus E and Poisson's ratio of the bar material.
From the figure shown, diameter of holes is 20 mm. Compute the net area for the plate if the thickness of the plate is 10 mm.
A 15mm flat bar shown in the figure is suspended vertically from the large end. If P=20kN is applied at shown. Determine the total change in length of the bar.
I need the answer as soon as possible
Work on Octive Online.
PROBLEM The centroid of the T-section shown is 1.6 inches above the base and x is 10. What should be the value of b to satisfy this condition? Input values in two (2) decimal places only without the unit. 1" x" 1" b
Subject: Civil Engineering