The shaft shown in the figure below is subjected to axial loads as illustrated. The diameters of segments AB, BC, and CD are 20mm, 25mm, and 15mm, respectively. If the modulus of elasticity of the material is 582 MPa. Determine the change of A to D length. Provide the answer in mm with two decimal points of accuracy. 100 mm 5KN 250 mm 150 mm 2kN 8kN A 5kN 2kN D B с Answer: 6kN

The shaft shown in the figure below is subjected to axial loads as illustrated. The diameters of segments AB, BC, and CD are 20mm, 25mm, and 15mm, respectively. If the modulus of elasticity of the material is 582 MPa. Determine the change of A to D length. Provide the answer in mm with two decimal points of accuracy. 100 mm 5KN 250 mm 150 mm 2kN 8kN A 5kN 2kN D B с Answer: 6kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The figure above is a skycam which is supported by 2 wires (assume that no wires holding at the top of this device). Assume that the wires are 0.05 inches diameter. If the skycam weighs 77 lbs, then the tensile stresses of wire 1 and wire 2 are Blank 1 ksi and Blank 2 ksi respectively. SN= 77
The stress-strain diagram for a bar of steel alloy is shown. Determine: a) The modulus of Elasticity for the material b) The proportional limit c) The ultimate stress Show a complete solution
Find the correct answer & solution please. Thank you.
QUESTION 2 The bar shown has a cross-sectional area of A Young's modulus of E and a length of L. It is carrying a force of F. Calculate the normal stress (a) in the bar. F F O k Your unique values to use are (everybody will get different values for every question): 45 KN 4256 mm A 426 mm² 220 GPa Your mark will be based entirely on the answer you select from below. 0 = 233 MPa o=151 MPa 0=171 MPa = 190 MPa a=202 MPa a = 92 MPa 0 52 MPa 0122 MPa 0=76 MPa 0= 145 MPa 0-62 MPa o=140 MPa d=212 MPa 0106 MPa 0-100 MPa
Give me right solution according to the question
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. If P = 75 kN, determine the following:a. Stress in the bronze segment.b. Stress in the aluminum segment.c. Stress in the steel segment.
L = 2.75
I need a quick solution within 15 minutes With my best wishesTon
Mechanics of deformable bodies. Two decimal places.
Quiz1
Q1\ A copper bar consists from three sections: sections 1 is of 25 mm diameter and 60 mm long, section 2 is of 15 mm diameter and 50 mm long and section 3 is 20 mm square and 40 mm long. The bar is subjected to an axial tensile load which induces a stress of 20 MN/m' on the smallest cross section. Determine the total increase in the length of the bar when the load is applied. For copper E=100 GN/m2.
A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in the figure. Axial loads are applied at the positions indicated. If P = 3000 Ib and the cross sectional area of the rod is 0.5 in^2, determine the stress in each section. Steel Bronze 4P | Aluminum | P 2 ft 3 ft 2.5 ft а. Stress (st) = 19 ksi, Stress (al) = 25 ksi O b. Stress (st) = 16.5 ksi, Stress (al) = 24.2 ksi O c. Stress (st) = 24 ksi, Stress (al) = 18 ksi O d. Stress (st) = 26 ksi, Stress (al) =17 ksi