A tensile force of 20 kN is applied to a specimen with a gage length of 50mm. It is then noted that the distance between the gage marks became 50.122mm. a,) What is the modulus of elasticity of the specimen if its diameter is 10mm? b.) What is the axial stress of the specimen? Solution must have Free Body Diagram/drawing.

Q: SITUATION 21 A rectangular steel block is 300 mm in the x direction, 200 mm in the y direction, and…

A:

Q: A cylinder with a 6.0 in. diameter and 12.0 in. length is put under a compressive load of 150 kips.…

A: D = 6 inL = 12 in P = 150 kipsE  = 8000 ksi v = 0.35

Q: 10-m-long steel rails of a railroad track (E,= 200 GPa and a = 117 x 10°C) were laid at a…

A: Using formula to find stress due to temperature rise

Q: Assuming you have been offered a job position as the lead Engineer to supervise the restoration of a…

A: Given: The crack length is 0.026 mm. The radius of curvature is 0.00028 mm. The theoretical fracture…

Q: P4: Two wooden boards are joined by cutting and gluing them together along the plane shown in the…

A: (a) If α=20° then, θ=90°-20°=70° The normal stress is calculated as,…

Q: 3. (A). Define the terms shear stress and shear strain, illustrating your answer by means of a…

A: shear stress : Shear stress is a force that tends to distort a material by causing it to slip along…

Q: O AF F. p0.2 p0.2 p0.2 S. 0.2-mm (0.2% of 100 mm=0.2-mm)- AL II R.

A:

Q: 120 4090 40 Dimensions in mm Im 2AN Determine the maximum tensile stress in the beam shown. O 7.31…

A: To find maximum tensile and compressive stress

Q: P- 3P 2P Steel Bronze Al A = 200 mm A = 400 mm A = 500 mm = 150MPA e= 100MPA c = 80MPA

A:

Q: A steel rod 30 mm X 20 mm is subjected to an axial load of 35 kN. The original length of the rod is…

A: Given data : Original length (L)=650 mmDecrease in length (∆L)=-5 mmAxial load (P)=35 KNDimension=30…

Q: Determine maximum shear stress

A: Given data : Maximum principal stress σ1=32 MPaMinimum principal stress σ2=-28 MPa

Q: Q1: A tensile test uses a circular test specimen that has a gage length of 50 mm and diameter = 20…

A: Given that,  gage length = 50 mm diameter = 20 mm loat at 0.2% yield point = 100,000 N gage length…

Q: A bar having a cross-sectional area of 700 mm² is subjected to axial loads at the positions…

A:

Q: Select the types of losses are both common for post tensioning and pre tensioning. a. relaxation,…

A: To determine: Types of losses are both common for post tesnsioning and pretensioning.

Q: please solve if uktimate tensile stregth is 800MPA. assume reliabilty of 98% fatigue fraction f of…

A:

Q: A sample material with circular cross-section tapers uniformly. Over a gauge length of 200mm, it…

A:

Q: A compound bar consists of (4) aluminum alloy bars of (2mm) diameter and (2) steel bars of (3mm)…

A: Thermal Stress : The stress produced by change in temperature in a material is known as thermal…

Q: ess of 12,5 induced in t 100 AAD

A:

Q: amplitude was 210 MPa. Compute the maximum and minimum stress. (Enter your answers to three…

A:

Q: Discuss Computation of Effective Stresses

A: Basic concepts- Effective Stress- Effective stress is a parameter in soil that is responsible for…

Q: The plastic modulus of a section is 5 x 10-4 m³. Its shape factor is 1.2 and the plastic moment…

A: Given data- Plastic modulus- Zp=5×10-4 m3, Shape factor SF=1.2, Plastic moment capacity- Mp=120…

Q: Challenge Problem 6: A 3/4 in. diameter punch is used to punch a hole through a steel plate 1/2 in.…

A: Given Load 60,000 lbDiameter 3/4 inThickness 1/2 inTo find out Shear stress

Q: Calculate the tensile stress when applied force of 1200ON on specimen of diameter of 7mm

A: tensile stress = tesile force / normal cross section area

Q: cylinder with a 6.0 in. diameter and 12.0 in. long is put under a compressive load of 150,000 lbs.…

A: Using formula

Q: A hollow cylinder with an OD of 100mm and an ID of 30mm, supports a load of 100kN. What is the…

A:

Q: Q. No 1. material. Discuss in detail the Stress Strain Diagram of ductile material and brittle |CLO…

A:

Q: Steel tape used in a tape measure has a thickness of 0.0065 in. If the allowable stress is 68 ksi,…

A:

Q: A Brinell test is performed on a steel using a 1.42 in. diameter indenter with a load of 67925 lbs.…

A: Given :- diameter of the indenter, D= 1.42 inch  Diameter of impression , Di= 0.8 inch  Applied…

Q: A flat bar of cross section 15 mm by 70 mm elongates 2.59 mm in a length of 1.3 m as the result of…

A: Axial stress is the ratio of load and the areaσ=PAσ=230,000N15×70 mm2σ=219Mpa

Q: The extruded plastic shape has dimensions of D = 28 mm, d = 24 mm, a = 82 mm, and t = 6 mm. (a)…

A: A1 = area of large circle of dia D                    distance of center of large circle from top =…

Q: When a round bar material with diameter of 37.5mm, length of 2.4 m, Young's modulus of 110 GN/m² and…

A: Given that :-K = Bulk ModulusWe will solve using the following formula:E = 9KG / (3K + G)Young’s…

Q: 4. Sample of steel bar has 50 mm length after performing tension test the final length was 50.2 mm,…

A:

Q: n the 28th day after concrete was mixed, a 6.00-in-diame a compressive testing at a load of 145 000…

A:

Q: Calculation: For center Loading: MR = 3PL / 2bd? Where: MR- modulus of rupture, psi (MPa) P= maximum…

A:

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.