When a round bar material with diameter of 37.5mm, length of 2.4 m, Young's modulus of 110 GN/m² and shear modulus of 42 GN/m² is stretched for 2.5 mm, its bulk modulus will be nearly (a) 104 GN/m² (c) 84 GN/m² (b) 96 GN/m² (d) 76 GN/m²

When a round bar material with diameter of 37.5mm, length of 2.4 m, Young's modulus of 110 GN/m² and shear modulus of 42 GN/m² is stretched for 2.5 mm, its bulk modulus will be nearly (a) 104 GN/m² (c) 84 GN/m² (b) 96 GN/m² (d) 76 GN/m²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The following observations were made during a tensile test on a mild steel specimen 40 mm in…

A: Given data : Tensile load P=40 KN Change in length ∆L=0.0202 mm Initial length L=200 mm Diameter of…

Q: ven the stress-strain data from a tension test, how do you find the following : a) The modulus of…

A: Solution on below attachments

Q: 5. A tensile test was done on a magnesium sample of original diameter and original length of 12mm…

A: To plot the stress v/s strain curve and to find the required parameters Note: as per the answering…

Q: A specimen is originally 300mm long and has a diemter of 11mm and it subjected to a force of 4kN.…

Q: A stainless-steel rod 16mm in diameter and 300mm long is put under a tensile load of 250 kN.…

A: Given data Initial diameter of the rod(Di) = 16 mm Then Area (Ai) = (π/4)*Di2 = 201.062 mm2…

Q: When a round bar material with diameter of 37.5 mm, length of 2.4 m, Young's modulus of 110 GN/m²…

Q: If Poisson's ratio of a material is 0.3, then the ratio of Young's Modulus to bulk modulus is (a)…

Q: 3-21. The stress-strain diagram for a polyester resin is given in the figure. If the rigid beam is…

A: P = 80 kN or 80,000 N d = 40 mmD = 80 mm

Q: Determine the following: a. Young's modulus within the linear portion b. Tangent modulus at a stress…

A: a).Young's Modulus : At the proportional limit, stress is directly proportional to strain stress α…

Q: (a) the modulus of elasticity. (b) Poisson's ratio. (c) the change in the bar width b.

Q: For a given elextic material, the Eastic Modulus E is 210 GPa and its Poission's Ratio is 0.27. What…

Q: O (MPa) 80 60 40 20 0.002 0.004 0.006 0.008 0.01 0.012 Figure 3 i) Determine the value of yield…

A: Dear student as per bartleby guidelines we are supposed to answer only first 3 sub parts. Kindly…

Q: 2) For a specific material having poisson's ratio -0.32, the percent of elastic modulus to modulus…

Q: A composite column is formed by placing a steel bar, 20 mm in diameter and 200 mm long, inside an…

A: Given:- The diameter of the steel bar = 20 mm The length of the steel bar = 200 mm The internal…

Q: Problem NO. 2. A student performed a tensile test in one of his samples, an aluminum specimen which…

Q: A 13 mm diameter tensile specimen has 50 mm gauge length. If the load corresponding to the 0.2%…

Q: A cylindrical tensile specimen has an undeformed diameter of 8.6 mm. It is subjected to a tensile…

A: Hello dear this is the solution of your problem The answer is found to be Change in diameter =0.37mm…

Q: When a round bar material with diameter of 37.5mm, length of 2.4 m, Young's modulus of 110 GN/m² and…

Q: DURING THE STRESS-STRAIN TEST, THE UNIT DEFORMATION AT A STRESS OF 30 MPa WAS OBSERVED TO BE 110 x…

Q: niform concrete slab is to be attached to two rods whose lowers ends are initially at the same…

A: Let W be weight of concrete slab. To find area of aluminium rod

Q: 2) A given material the linear limit is 1.8 * 106 N/ m? and the ultimate compressive strength is 1.8…

Question

When a round bar material with diameter of
37.5mm, length of 2.4 m, Young's modulus of
110 GN/m² and shear modulus of 42 GN/m² is
stretched for 2.5 mm, its bulk modulus will be
nearly
(a) 104 GN/m²
(c) 84 GN/m²
(b) 96 GN/m²
(d) 76 GN/m²

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: State the given data

VIEW

Step 2: Determine the bulk modulus

VIEW

Solution

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A composite column is formed by placing a steel bar 20 mm diameter and 200 mm long, inside an alloy cylinder of the same length whose internal and external diameters are 20 mm and 25 mm respectively. The column is then subjected to an axial load of 50 kN. Modulus of elasticity for steel and alloy is 200000MPa and 70000MPa respectively. Which of the following gives the stress in the steel bar? a. 132.98 MPa b. 46.54 MPa c. 74.80 MPa d. 166.23 MPa
A 13 mm diameter tensile specimen has 50 mm gauge length. If the load corresponding to the 0.2% offset is 6800 kg, the yield stress will be nearly 1. 31 kg/mm² 2. 43 kg/mm² 3. 51 kg/mm² 4. 63 kg/mm² X
A cylindrical piece of steel, with a diameter of 60mm and length 100 mm, is subjected to an axial compressive force of 40,000 kg. If bulk modulus is 1.7 x 106 kg/cm² and poisson's ratio is 0.25 than the change in volume of the cylindrical piece is
A cylindrical piece of steel, with a diameter of 60mm and length 100 mm, is subjected to an axial compressive force of 40,000 kg. If bulk modulus is 1.7 x 106 kg/cm² and poison's ratio is 0.25 than the change in volume of the cylindrical piece is?
The solid circular drill rod AB is made of a steel that is assumed to be elastoplastic with τY = 22 ksi and G = 11.2 × 106 psi. Knowing that a torque T = 72 kip·in. is applied to the rod and then removed, determine the maximum residual shearing stress in the rod. The maximum residual shearing stress in the rod is ksi.
When a round bar material with diameter of 37.5 mm, length of 2.4 m, Young's modulus of 110 GN/m² and shear modulus of 42 GN/m² is stretched for 2.5 mm, find its Bulk modulus.
Q.3 The compressive strength of (Ø25×25) cm cylinder is 30 MPa at an age of 21-day, determine the direct tensile strength at the age of 7-day.