A spherical pressure vessel has an outer diameter of 75 mm and a wall thickness of 10 mm. It's made of a steel having the yield strength (Sy) of 300 MPa. If the largest principal normal stress is not to exceed 80% of the yield strength, determine the maximum internal pressure this pressure vessel can withstand. The pressure vessel is considered thick-walled spherical pressure vessel.

Q: The homogeneous 1000-lb plate is suspended from three cables. Determine the smallest diameter cable…

A: As per honor code and answering guidelines I can answer 1st question at a time (since both are not…

Q: Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 53 kN if it…

A: Given: Here is the given data, Axial force, F=53 kN Stress, σ=52 MPa dido=26 To find: The outer…

Q: A steel tube of 200 mm external diameter is to be shrunk onto another steel tube of 60 mm internal…

A: For inner tube: Write the expressions for A and B for thick cylinder. At r=0.030,…

Q: Deep sea pipelines are used to transport oil and gas across large distances, at depths greater than…

A: Height of the pipe, h = 2000 mrmin = 400 mDiameter of the pipe, d = 24 inch = 240.0254 = 0.6096 mt=…

Q: Determine the normal stress in each section of the assembly. The diameter of the solid shaft of each…

A:

Q: QUESTION 3: Determine the equivalent state of stress for an element oriented 60° counterclockwise…

A:

Q: A steel tank has an inside diameter of 3 m and 6 m high contains gasoline with a relative density of…

A:

Q: A thick-walled cylindrical pressure vessel having centroidal radius r and variable wall thickness t…

A: Understand that the maximum von Mises stresses occur at thickness t0. Consider that the ends of the…

Q: A spherical and cylindrical gas tank has the same inner radius of 1.5 m. Which of the  two tanks can…

A: Given   Diameter, d = 2 x 1.5 = 3 m            Stress = 15 MPa    Thickness, t = 20 mm Find   The…

Q: 7. A thick-wall cylinder is made of steel (E-200 GPa and v=0.29), has an inside diameter of 20 mm,…

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the…

A:

Q: For a closed end cylinder where the inner radius is 20 mm and outer radius is 40 mm, and the…

A: Sddd

Q: Question 12 A 7-ft diameter spherical tank is subjected to an internal pressure of 45 psf. If the…

A:

Q: A closed cylindrical tank containing a pressurized fluid has an inside diameter of 320 mm and a wall…

A:

Q: A hemispherical pressure vessel with a diameter of 2 m and a wall thickness of 30 mm is filled with…

A: Givend=2m=2000mmt=30mmP=15MPa

Q: An open cylindrical tank E mm in diameter and made of F mm thick plate is subjected to an internal…

A: According to the given information we have a diameter of the cylinder is 6 mm. the thickness of the…

Q: 5 mm B. ON A 1900 N 800 M

A: given:

Q: Air pressure in the cylinder is increased by exerting forces P = 3 kN on the two pistons, each…

A: Force, P = 3 kN = 3000 N Radius, r = 45 mm = 0.045 m Wall Thickness, t = 2 mm = 0.002 m

Q: Answer the following

A: Given data The initial temperature of the bar is T1=72°F The final temperature of the bar is T2=0°F…

Q: A tank 10 m high and 2 m in diameter is 15 mm thick. The max tangential stress is ? The max…

A: Given data  height = 10 m diameter = 2 m thickness = 15 mm find the maximum tangential stress and…

Q: ng thin walled cylindrical shell, closed at both the ends, is subjected to an internal pressure.…

A: Given:Suppose,The pressure inside the cylinder=PThe thickness of shell= tThe diameter of shell is =d

Q: The steel pipe in (Eigure 1) has an inner diameter of 3.54 in, and an outer diameter of 3.79 in.…

A: To find:The principal stresses at point .Given:The outer diameter of the pipe is .The inner diameter…

Q: A pipe has an outside diameter of 0.8 inches and inside diameter of 0.19 inches. A force of 105 lbs…

A: Given     Outside diameter, d2 = 0.8 in        Inside diameter, d2 = 0.19 in…

Q: A steel pipe 1.5m in diameter is required to carry an internal pressure of 650kPa. If the allowable…

A:

Q: A cylindrical steel pressure vessel with a diameter of 1200 mm and a wall thickness of 20 mm is…

A:

Q: material is 280 MPa. Using a safety factor of 1.5, determine the material thickness of the tank in…

A:

Q: No Normal stress acts on the neutral axis. Is it true or false? How?

A: When a beam is subjected to a bending moment the beam undergoes either hogging or sagging. In both…

Q: A spherical pressure vessel 4 ft. in diameter with a wall thickness of 0.25 in is subjected to an…

A:

Q: 3. Find the proper thickness of 900 mm cast-iron pipe under a 95m head of water with a working…

A:

Q: 2m Z 1.5 kPa R T I'm

A:

Q: A spherical pressure vessel of 5.7 meter diameter is subjected to an internal pressure of 3.8 MPa.…

A: Given data  d=5.7 mP=3.8 MPat=5 mm Here, d is the diameter, P is the pressure on the vessel.  Now we…

Q: 1. The cylindrical pressure vessel has an inner radius of 1.25 m and a wall thickness of 15 mm. It…

A: Given data :- The inner radius = 1.25 m                         The thickness of wall = 15 mm…

Q: A thick cylinder has an outside diameter of 100 mm and an inside diameter of 60 mm. It is…

A:

Q: m high and 5 m in diameter is to be filled with water. Find the minimum thickness of the tank…

A:

Q: A compound cylinder is made by shrinking a jacket with an outer diameter of 200 mm on a hollow…

A:

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.