A solid circular rod of diameter d undergoes a bending moment M=1300 lbf-in inducing a stress o=32 M/(?), Using a material strength of 25 kpsi and a design factor of 2.5, determine the minimum diameter of the rod. Using Table A-17 select a preferred fractional diameter and determine the resulting factor of safety.

A solid circular rod of diameter d undergoes a bending moment M=1300 lbf-in inducing a stress o=32 M/(?), Using a material strength of 25 kpsi and a design factor of 2.5, determine the minimum diameter of the rod. Using Table A-17 select a preferred fractional diameter and determine the resulting factor of safety.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A horizontal beam AC is supported by a square bar BD. Assume that the pin placed at B is adequate to support the load desired to size the bar. The factor of safety for creep failure is FS=3.0 Determine the required thickness (t) of the rectangular bar BD. Data: P=10KN L= 3m h= 2m b= 25mm If = 250 MPa
Please full solution with big and clear handwriting
Machine Element Design
4. A beam has fluctuating bending moment and is not rotating. The bending moment has a maximum of 1kNm and a minimum of 100kNm. The beam is made of AISI1020CD steel with a square cross section. There are no stress concentrations. a. Determine the fully corrected endurance limit as a function of the cross section (cross section unknown) b. Determine the required size for a factor of safety of 2 using the Gerber Fatigue Failure Theory
Dr. (ny) A = 5.52 تمارين : واجب بيتي 1. The solid steel shaft 100 mm in diameter and 8 m long was made of AISI 1020 HR steel is subjected simultaneously axial to an compressive force of 200 kN and a torque T. find the maximum applied torque T depending on the maximum shear stress, if the factor of safety is 1.5 and Ssy === Sy (Neglect buckling) 600 kN 30 T 100 mm 600 kN Prepared by Dr. Hazim Khale anc dir the dia BC (b to ca th th n
1. A safety valve must start opening when the force is equal to 777.48N, and be fully open when (20mm spring compression) at a force of 812.82N. The spring should not be more than 90mm outside diameter, with the maximum shear stress under 1100MPA. The material used has a shear modulus of (G = 77.2 GPa). Determine the springs Mean Diameter, Wire diameter, Number of active coils and unloaded Length. D C = d 4С — 1 0.615 8FD Kw T = K,- nd³ + 4С — 4 C - 8FD³N y = 8FD³N dªG 1+ 2C² dªG
A round bar of length /= 100 mm, diameter d 20 mm, is subjected to an axial force P- 500 N, a transverse force F5000 N, and a torque T-50 N.m. The material is steel with Sy 480 MPa. Using the distortion energy (Von Mises) yield criterion, calculate the safety factor at points A and B. 20 D. Select one: O a. NA = 7.897, Ng = 4.958 O b. NA = 0.624, Ng- 4.352 Oc. NA 4.768, Ng 2.346 O d. NA = 0.749, Ng =5.223
A bolted lap joint using ISO 5.8 bolts and members made from cold-drawn SAE 1040 steel is shown in the figure. Assume the bolt threads do not extend into the joint. Find the tensile shear load F that can be applied to this connection to provide a minimum factor of safety of 2.5 for the following failure modes: shear of bolts, bearing on bolts, bearing on members, and tension of members. 40 ↑ 70 40 ↑ 80 M20 × 2.5 20 20
01: A hollow steel tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in, is fastened to a solid aluminum rod (2) that has a 2 in. diameter and a solid aluminum rod (3) that has a 1.375 in. diameter (E -30,000 ksi, E-10,000 ksil. The bar is loaded as shown in figure below, Determine: (1) the displacement of point D with respect to the fixed support at A. (2) the maximum normal stress in the entire axial assembly. (3) the normal strain in the steel tube (1). 34 kips 18 kips 25 kips 18 kips 34 kips 60 in. 40 in. 30 in.
Required information A solid square rod is cantilevered at one end. The rod is 0.6 m long and supports a completely reversing transverse load at the other end of ±1.7 kN. The material is AISI 1080 hot-rolled steel. If the rod must support this load for 5 x 104 cycles with a design factor of 1.5, what dimension should the square cross section have? Neglect any stress concentrations at the support end. What will the strength of the metal be at 5 x 104 cycles? The strength of the metal at 5 x 104 will be MPa.
Given: Tie rods in a press machine are steel alloy AISI 5160 OQT 1000 - Diameter: D = 2.00 in. E = 30 x 106 psi - Length: L = 68.5 in. - Axial tensile force: F= 40,000 Ib. %3D Required: The elastic deformation of the tie rods is _in. 0.039 0.059 0.049 0.029