A simply supported beam is made of four 50 mm x 150 mm wood planks that are fastened by screws as shown in the cross section below. The beam carries a concentrated load at the middle of its 3.6 m span that causes a maximum bending stress of 9.65 MPa in the wood section. Determine the largest allowable spacing/pitch if the shear strength in each screw is limited to 890 N. O a. 59.02 mm O b. 51.05 mm O c. 64.52 mm O d. 35.66 mm

Q: What is the basic procedure in setting up a CPM Schedule?

A:

Q: Activity IPA Activity IPA D B D, E C, F, G C, G C A, B H, I FGHH

A:

Q: What kind of documentation should be done by the field personnel?

A: Few accurate notes were maintained, and all of the contractor 's correspondence was informal in…

Q: According to the information given in the table, draw the project (in a circle) and indicate it with…

A: Dotted line represents Dummy network.

Q: Is the Resident Project Representative responsible for ordering supplies and equipment?

A: The Resident Project Representative (RPR) person should work on full time basis whereas the engineer…

Q: Which type of information can be added to BIM? All the answers are correct Schedule Cost…

A: Answer:- All the answers are correct. BIM: Building Information Modelling is the holistic process of…

Q: What are some of the administrative procedures?

A: The construction administration is administrative assistance offered by an engineer, or…

Q: fill in the graph and color critical path red   please help

A: To fill in the boxes in the graph, we need to calculate the Early Start (ES), Early Finish (EF),…

Q: Question 24 Resource is a situation in which more resources than available are assigned to an…

A: Answer Resource Allocation Resource allocation is the way or process used to assigning and…

Q: Question 1 A draw schedule is typically proposed by a contractor. O True False

A:

Q: What instructions are given to the field personnel?

A: - Field personnel is a position of an employee who need to work at non office place, mostly at work…

Q: What are the other sources for change orders?

A: The change order can referred as a variation order, it is a work that has been excluded or added to…

Q: Please make a PERT CPM use the activity and duration below. Also use the format stated. PLEASE DON'T…

A: I will create a PERT CPM (Program Evaluation Review Technique Critical Path Method) chart using the…

Q: Define the term CQC Representative?

A: The contractor is responsible for the betterment of the project. The contractor also responsible to…

Q: When do the conflicts in plans occur?

A: In project management several projects encounter common categories of conflict. It's the…

Q: Step 1 – Develop a dependency table showing activity relationshipsStep 2 – Layout an AON network…

A: Creating the AON Network Diagram:AON network diagram based on the provided activities and…

Q: Who is responsible for preparing the weekly reports for the project?

A: The Project Manager is responsible for preparing and maintaining the weekly reports for the project.…

Q: What is S-curve scheduling?

A: To define the S-curve scheduling we need to understand the S-curve. An S-curve could be a…

Q: What preparations can be made for close out project?

A: Project closure activities make sure the recording project documents, archiving in structure method…

Q: What is a job progress scheduling?

A: The construction management has the responsibility of supervising the planning, scheduling,…

Q: Identify which system of network scheduling is best adapted to each of the following types of work:…

A: Since, we answer only three sub-parts, will answer the first three. Please resubmit another question…

Q: Write the five basic project planning steps when setting up a CPM Schedule?

A: Critical path is defined as the path when the duration of activities along this paths adds up to…

Q: A simple house project can be structured as follows (9 work packages total): • Design: Ground plans…

A: Here's a proposed Work Breakdown Structure (WBS) with some additional sub-tasks:1. House Project1.1…

Q: 10. Given the diagrams in Figure P5.1 of progress on individual work pack- ages of a project, answer…

A: Given Data : BCWS = budget cost of work scheduled (planned value) ACWP = Actual Cost of Work…

Introduction to Engineering Design

Students are often confused with engineering and design. The term engineering design has two words with different meanings, engineering, and design. The term engineering implies applications of laws and principles of science to design and analyze physical structures and components. In civil engineering, students apply the concept of physics and chemistry to design and build structures and buildings. In engineering disciplines, the term design means determining the dimensions, loads, and associated influences on the component due to the applied loads such as stresses and deformations. The estimation of such parameters is crucial to make the component or structure foolproof.