A simplified diagram of a racing cars suspension and wheel is used to design the bars and pins. The force that the suspension must withstand can be considered to be a vertical force, F = 1.5 kN, acting vertically upwards at B. Calculate the minimum radius of the bars AB and BC if the maximum allowable stress oalow= 80 MPa. Also, calculate the minimum radius of the pin at A if this pin is in Double Shear and the maximum allowable shear stress Tallow = 50 MPa

A simplified diagram of a racing cars suspension and wheel is used to design the bars and pins. The force that the suspension must withstand can be considered to be a vertical force, F = 1.5 kN, acting vertically upwards at B. Calculate the minimum radius of the bars AB and BC if the maximum allowable stress oalow= 80 MPa. Also, calculate the minimum radius of the pin at A if this pin is in Double Shear and the maximum allowable shear stress Tallow = 50 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5
A simple torsion-bar spring is shown. The shear stress in the steel [G= 11,500 ksi] shaft is not to exceed 10800 psi, and the vertical deflection of joint D is not to exceed 0.425 in. when a load of P = 3100 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 84 in., b = 32 in., and c = 36 in. Part 1 Answer: T = a i D P B Calculate the torque being applied to the shaft at point B. b C lb-in
Solve please
number 5
Use the graphical method to construct the shear-force diagram and identify the magnitude of the largest shear force (consider both positive and negative). The ground reactions at the wall of the cantilever are provided. L₁= 14.75 ft L₂ = 7.75 ft Vc = 91.50 kips Mc = 706.4375 kip-ft 20 kips 6 kips/ft L₁ 103.50 kips 68.50 kips 91.50 kips O 79.50 kips O 114.50 kips 70 kips BO 12 kips/ft L2 O Vc Mc
Indicate your assumptions, write the given and make an organized solution.
ı need solution
An idealized model of a thin-walled convertible car body cross-section is shown in figure Q16. The effect of doors and windows has been ignored. The car has vertical side walls of thickness t1 and length 1 m and a horizontal base of thickness t2 and length 1.9 m. It is constructed from aluminium with a shear modulus of 24 GPa. t₁ = 15 mm t2 = 15 mm a. For this open section determine the torsional stiffness? Give your answer to 3 significant figures in Pa m4 and non-scientific notation e.g. 10000 rather than 10e05. Do not include units in your answer Note that for an open section, the total area moment JT is the sum over all plates i as given by equation (1) below. Ir = = = Ei bit? Torsional stiffness = GJT t₂ 1.9 m 1m Figure Q16 - idealised model of a thin-walled convertible car body
Parvinbhai
The compound bar carries the axial forces P and 2P. Find the maximum allowable value of P (in lbs) if the working stresses are 40 ksi for steel and 20 ksi for aluminum, and the total elongation of the bar is not to exceed 0.2
the cröss-stCtions e-e and f-f, respectively, when a torque T = 800 Nm is applied at point B. Take the shear modulus G= 80 GPa. Qier te cruhe The stepped shaft shown below is rigidly attached at both ends. The shaft segments AC and CD have (a) Find the reactions at both ends. (b) Determine the shear stress developed at points K and L on a cross-section taken from the shaft between points B and C. (c) Find the angle of twist at point C. 30 mm T=800 N.m 20uun 50 mm Activate Windou Section ffSings 200 mm 400 mm 300 mm Section e-e
A simple torsion-bar spring is shown. The shear stress in the steel [G= 11,500 ksi] shaft is not to exceed 10000 psi, and the vertical deflection of joint D is not to exceed 0.600 in. when a load of P = 4300 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 88 in., b = 22 in., and c = 40 in. Part 1 * Incorrect Answer: C T= i 5.468 B Calculate the torque being applied to the shaft at point B. b Ib-in