A sample is run on a TLC plate and gives a single spot as shown below on the left. However, the solvent was not allowed to run up the plate very far, and so the experiment was repeated with a much larger solvent distance as shown on the right below. What would be the approximate Rf value of the spot for the repeat experiment on the right? solvent line solvent line start line start line 01.0 0.9 © 0.5 0.1

A sample is run on a TLC plate and gives a single spot as shown below on the left. However, the solvent was not allowed to run up the plate very far, and so the experiment was repeated with a much larger solvent distance as shown on the right below. What would be the approximate Rf value of the spot for the repeat experiment on the right? solvent line solvent line start line start line 01.0 0.9 © 0.5 0.1

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Question 8 Borneol and isoborneol were formed in a reaction. Use the following GC chromatogram of the isoborneol and borneol dissolved in acetone to answer the question: Please note that the question is below the chromatogram. 15000 14000 12000 10000- 8 8000. 6000 0 10 0.5 GC of Bomeal and Isobomeol 0.82 Component Acetone Isoborneol Borneol 1.5 Time (min) 8.06E+04 4.84E+04 Peak Area Boiling Point (deg. C) 1.61E+04 56 210 3 213 2.14 2.45 The numbers above each peak represent the time that it took the peak to come out of the column and be detected. What is the term given to this value?
A silica TLC plate is developed in a mixture of solvent system/mobile phase. The solvent travels 30 mm up the plate Analyte #1 travels 9 mm up the plate Analyte #2 travels 16 mm up the plate Which analyte is more polar, and what is its Rf? Analyte #1, Rf = 0.53 Analyte #2, Rf = 0.53 Analyte #2, Rf = 0.3 Analyte #1, Rf = 0.3
Pre-lab question 2 Homework Unanswered With the methods and GC columns used in organic labs, the volatility of the nitrotoluene products is the factor that is most responsible for the separation of the products in the GC. Predict the order of the nitrotoluene retention times expected in your chromatogram. Order from lowest (top) to highest (bottom) retention time. Drag and drop options into correct order and submit. For keyboard navigation... SHOW MORE V para-nitrotoluene II ortho-nitrotoluene meta-nitrotoluene Unanswered A Submit Pre-lab question 3 Homework Answered E3 Ful What is the active electrophile in the nitration of toluene exneriment? IMG-4268.jpg IMG-4267.jpg CamScanner 02-.pdf Show ... II II
Pls help ASAP. Pls show all work and calculations.
Plant pigments in spinach were separated with TLC with cellulose as thestationary phase and 80/20 diethyl ether/acetone mixture as themobile phase. If needed, the solvent structures in the lab Appendix.1. Determine the Rf values of each plant component on this TLC plate.2. Arrange the plant components from most polar to most nonpolar. Please answer both 1 and 2 (picture below is the same question attached )
Based on your value of Ksp1 what is the solubility of borax in the room temperature solution? Trial 1: 0.0141 T2: 0.015 AVG: 0.0139 Temp: 293.15K
The figure below shows a typical separation of several fat-soluble vitamins by HPLC. The x-axis is retention time in minutes. From the graph try to estimate retention times for peaks 2 and 3. Retention time peak 2 = Retention time peak 3 = Assume that w1/2 is 0.15 minutes for peak 2 and 0.16 minutes for peak 3. Assume that tm is 2.00 minutes. How much time does gamma-tocopherol spend in the stationary phase? From tr and w1/2 find N for the peak that elutes first. From tr and w1/2 find the resolution of peaks 2 and 3 Calculate α for these peaks. If the flow rate for the column is 1.2 mL/minute what is the retention volume for peak 4?
if you perform QC for sodium on a chemistry analyzer and the value is greater than 2SD above the mean. This is the second day that this level of control has been >2SD for that analyte. You mixed the vial and repeated. QC was still "out". It is time to troubleshoot. What do you do?
determine the possible molecular formula for this compund
I got 1.55 but it's not a choice so idk what to do