A sample in variable head permeameter with 80 mm in diameter and 180 mm height can estimate the permeable of water in 10 x 103 mm/sec. If the design of head in stand pipe falls from 1,000 mm to 500 mm in 3 minutes, compute the size of stand pipe needed for this test based on the assumptions of Bernoulli's Equation and Darcy Law.

A sample in variable head permeameter with 80 mm in diameter and 180 mm height can estimate the permeable of water in 10 x 103 mm/sec. If the design of head in stand pipe falls from 1,000 mm to 500 mm in 3 minutes, compute the size of stand pipe needed for this test based on the assumptions of Bernoulli's Equation and Darcy Law.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Sample 2: Mass with empty mold M1 Mass of soil and mold M2 Hydraulic Head h Time interval t Volume V 145 g 250 g 950 mm 0.34 min 0.0046 L 145 g 260 g 900 mm 0.33 min 0.0049 L 145 g 228 g 922 mm 0.30 min 0.0051 L 145 g 281 g 915 mm 0.29 min 0.0044 L 145 g 219 g 908 mm 0.39 min 0.0042 L The diameter of the mold = 2.5 cm, Length of the sample = 0.3 m can u pls Find the permeability coefficient Mass of the soil Bulk Density Dry Density thank you Void Ratio
Liquids A, B and C, in the containers shown, have SG of 0.60, 1.00 and 1.60 respectively. At what elevation (EL. C) will the liquid C stand in each of the piezometer tubes? Round your answer to the nearest hundredths. Pair = 12.5 kPa EL. 8 A (SG =) EL. 6 B (SG =_) %3D EL. 2 C (SG = EL. 0
For a falling head permeability test, the following are given: Length of specimen = 375 mm Hydraulic conductivity = 1.72 m/min. Area of specimen = 1875 mm2 What should be the area of the standpipe for the head drop from 625 mm to 300 mm in 480 seconds? Select the correct response: 88.63 mm2 56.24 mm2 93.74 mm2 53.18 mm2
7.7 In a constant-head permeability test, the length of the specimen is 200 mm and the cross sectional area is 78.5 cm². If k = 2.1 x 10-2 cm/sec, and a rate of flow of 130 cm³/min has to be maintained during the test, what should be the head difference across the specimen?
In a liquid limit test using Fall cone apparatus, the following readings were recorded. While in the plastic limit test, the following data were obtained: Weight of soil + container = 22.12 grams Weight of dry soil + container = 20.42 grams Weight of container = 13.07 grams Determine the ff. (SHOW COMPLETE SOLUTION AND GRAPH) A. Find the liquid limit B. Compute the plastic limit. C. Find the liquid limit. D. Find the plastic limit. 40% 45% 50% 58% Water Content 12 16 21 35 Penetration of cone(mm) -PLS SHOW COMPLETE SOLUTION AND GRAPH. SHOW YOUR ANSWER IN 4 DECIMAL PLACES. I'LL RATE, THANKS!
USING FOL Differential Equation APPLICATION SOLVE THE FOLLOWING PROBELM AND SHOW COMPLETE SOLUTION AND FINAL ANSWER.In a tank of 100 liters of brine containing 50 kg total dissolved salt. Pure water is allowedto run into the tank at the rate of 3 liters a minute. Brine runs out of the tank at the rateof 2 liters a minute. The instantaneous concentration in the tank is kept uniform bystirring. How much salt is in the tank at the end of 1hour?
Porous stone Soil specimen h L Porous stone Graduated flask Refer to the constant head permeability test shown in the figure above. For a test, these values are given: L = 320 mm Area of the specimen A = 180 cm? Constant head difference h = 500 mm Water collected in 3 min Q = 640 cm³ Calculate the hydraulic conductivity in cm/s. (Enter your answer to three significant figures.) JU
A sample of sand is subjected to a constant head permeability test. The sample diameter is 60 mm and its length is 130 mm. Under an applied head of 60 cm, 119 cm³ of water flows through the sample in 5 minutes. Determine (a) the coefficient of permeability, and (b) the discharge velocity.
The Professor demonstrated the proper application of the procedure by analyzing a 50 mL sample of water from a local lake (Rivers Parkway) via titration with a standard solution of EDTA 0.0100 +0.0001 M standard. This sample consumed 5.00 mL to reach the Total Hardness (TH) end point; therefore, the TH of the lake was determined to be XX ± YY mg/L as CaCO,.
A falling head permeability test was run on a soil sample 9.60 cm in diameter and 10 cm long. The head at the start was 90 cm. The coefficient of permeability of the soil was found to be 5 x 10-6 cm/s. The diameter of the standpipe was 1 cm. What is the rate of flow after 30 minutes? Select the correct response: 10.79 cm/hr 11.04 cm/hr 9.10 cm3/hr 6.46 cm3/hr
Read the question carefully and give me right solution. Provide detailed solution with clear calculations. The hydraulic conductivity of a soil sample, measured at 25C, was 0.005 cm/s using water as the test fluid (density = 997.2 [kg m–3 ], viscosity = 0.0008872 [kg m–1 s –1 ]. Determine the conductivity for ethanol at 10C, density = 798 [kg m–3 ], viscosity = 0.001394 [kg m– 1 s –1 ]
Q. Determine the kinematic viscosity at the average temperature and determine the Reynolds number and type of flow using the data shown below and table values: Data obatined from a Reynolds Number test: Water temperature at the beginning of the experiment = 25 oC Water temperature at the end of the experiment = 30 oC The Volume of water collected in 25 seconds = 240 ml Pipe diameter, d= 10 mm. (use eq'n reynold's number, Re = VD/v