While in the plastic limit test, the following data were obtained: Weight of soil + container = 22.12 grams Weight of dry soil + container = 20.42 grams Weight of container = 13.07 grams Determine the ff. (SHOW COMPLETE SOLUTION AND GRAPH) A. Find the liquid limit 3. Compute the plastic limit. C. Find the liquid limit. D. Find the plastic limit.

While in the plastic limit test, the following data were obtained: Weight of soil + container = 22.12 grams Weight of dry soil + container = 20.42 grams Weight of container = 13.07 grams Determine the ff. (SHOW COMPLETE SOLUTION AND GRAPH) A. Find the liquid limit 3. Compute the plastic limit. C. Find the liquid limit. D. Find the plastic limit.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

One of the most challenging problems in environmental remediation is isolated blobs of contaminated fluid that become trapped in soils by capillary forces (i.e., surface tension). The pore space can be analyzed by analogy to a thin-diameter glass tube. Under the conditions given, what is the maximum length of water, I, that can be retained in the vertical glass tube shown? [mm] • contact angle 0 = 0⁰ • surface tension o= 72 dyn/cm = 0.072 N/m • tube diameter D = 2.0 mm • ● neglect the small volume of water above the meniscus the weight of water completely removes the curvature in the lower air-water interface
Given below is the result of a sieve analysis done on a soil sample. determine the value of the coefficient of uniformity
Kindly give me right solution with clear calculations
Cumpute the plasticity index and liquidity index
4. A series of tests are run on a HMAC Sample. The following data is given to you:% AC (Pb) = 10 %Gb = 1.040Gsb = 2.51Gmm = 2.696Mass of compacted HMAC sample = 840 grMass of compacted HMAC sample submerged in water = 512 grMass of compacted HMAC sample, SSD condition = 847 gra. Based on the above information what is the Gmb? b. Based on the above information what is the of VTM? c. Based on the above information what is the of VMA? d. Based on the above information what is the of VFA?
Atterberg's limits Problem 4.3 Results from liquid and plastic limit tests conducted on a soil are given below. Liquid limit tests: Number of Moisture blows, N content (%) 13 33 18 27 29 22 Plastic limit tests: Weight of Can 20 g Weight of Can + Moist soil = Weigh of Can + Dry soil 56.2 g 48.4 g a. Draw the flow curve and obtain the liquid limit. b. Calculate Plastic Limit b. What is the plasticity index of the soil?
Correct answer please.
A) compare by drawing between the Clay minerals of 1/1 and clay minerals of 1/2
Someone can help me with this one. Please
Analysis of Results1. Summarize you Hardness results.2. Does the hardness of your sample fall within the expected range?3. How would the water be classified in terms of hardness (soft, moderately hard, hard, etc.)?
Given below is the result of a sieve analysis done on a soil sample.Sieve No. Diameter Percent Passing %4 4.750 9510 2.000 8220 0.850 7340 0.425 5360 0.250 23100 0.150 14200 0.075 7Pan --- 0Determine the value of the coefficient of uniformity
Read the question carefully and give me right solution. Provide detailed solution with clear calculations. The hydraulic conductivity of a soil sample, measured at 25C, was 0.005 cm/s using water as the test fluid (density = 997.2 [kg m–3 ], viscosity = 0.0008872 [kg m–1 s –1 ]. Determine the conductivity for ethanol at 10C, density = 798 [kg m–3 ], viscosity = 0.001394 [kg m– 1 s –1 ]