A constant-head permeability test is performed in a laboratory where the soil sample is 25 cm in length and 6 cm2 in cross-section. The height of the water is maintained at 2 ft at the inflow end and 6 in. at the outlet end. The quantity of water flowing through the sample is 200 ml in 2 minutes. (a) Make a sketch of the described conditions.

A constant-head permeability test is performed in a laboratory where the soil sample is 25 cm in length and 6 cm2 in cross-section. The height of the water is maintained at 2 ft at the inflow end and 6 in. at the outlet end. The quantity of water flowing through the sample is 200 ml in 2 minutes. (a) Make a sketch of the described conditions.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Subj: civil engineering / soil mechanics The volume of soil sample measured before oven drying is 120 cm3. The dried weight of the soil sample is 122 g. The percent passing of No. 200 sieve is 63% and the group index is 12.82. The liquidity index and plastic limit are 1.25 and 7.6%, respectively. If the specific gravity of soil is 2.70, compute the following: a. Void ratio b. Dry unit weight c. Dry unit weight at zero air voids
Homework #3 The results of a standard Proctor test are given in the following table. a. Determine the maximum dry unit weight of compaction and the optimum moisture content. Given: mold volume =943.3 cm'. b. Determine the void ratio and the degree of saturation at the optimum moisture content. Given: G, = 2.68. Trial no. Weight of moist soil in the mold (kg) Moisture content (%) 1.78 5.0 1.87 7.5 3 1.95 10.0 4 1.98 12.5 5 2.02 1.97 15 17.5 7 1.90 20.0
Two soil specimens with identical geometric dimensions were subjected to falling head permeability tests is the laboratory under identical conditions. The fall of water head was measured after an identical time interval. The ratio of initial to final water heads for the test involving the first specimen was 1.25. If the coefficient of permeability of the second specimen in 5 times that of the first, Then what is the ratio of initial to final water heads in the test involving the second specimen ?.
Please show all calculations. I need help understanding my homework, Thank you!
A natural soil deposit is to be used for a geotechnical engineering project. Laboratory test results indicate that the soil possesses liquid and plastic limits of LL = 30% and PL = 22%, respectively. In addition, the sieve analysis has produced the following information: • % Passing Sieve No. 4 (4.75 mm) % Passing Sieve No. 200 (75 μm) • Coefficient of Uniformity C₁ 100% 8% 1.590 0.012 Coefficient of Curvature Co (a) Determine the soil's classification in accordance with the Unified Soil Classification System (USCS). (b) To further improve the soil's shear strength performance, the natural soil deposit (possessing an in- situ water content of w = 14%) was compacted in-situ and has achieved a saturation degree of S = 85%. If the specific gravity of soil solids is G, = 2.6, determine the soil's dry and bulk unit weights (ya and y) in its current compacted state.
Solve this problem..
Q6:For the beam shown, Draw (S.F.D)and (B.M.D). 4KN/m 8KN/m 3m तरीत 4m ** 3m 30KN.m
i need the answer quickly
Consider that a 58.7 gram sample of dry soil is used in making a mechanical analysis by using the hydrometer method. The laboratory was held at a constant temperature of 20 C (68 F). The 40 s hydrometer reading was found to be 32.5 and the 8 hr hydrometer reading was 15.5. The percentage of sand in this soil sample is (note, a 58.7 gram sample is used here): Your Answer: Answer units
Soil mechanics
Hello can any one help me with this
The results of a Standard Proctor test are given in the following table. Moist Weight of Wet Sol Moisture Content in the mold (Ib) Trial (%) 26 4.08 28 4.12 30 4 4,18 32 Determine: 1. Maximum dry unit weight in Ib/ft^3 (4 decimal places) 2. Optimum water content in % (4 decimal places)