A rectangular suppressed weir, 1 m in length is used in a reservoir with an area of 50 square yards. During dry season, it was requested for 40 cubic meters per second of water to be discharged using the weir. If the discharge coefficient is 0.72 and the initial head of the weir was 1.20 m, how long will it take for the weir to discharge the demand as stated in the problem? 66.25 s O 43.85 s O 36.15 s 28.64 s

A rectangular suppressed weir, 1 m in length is used in a reservoir with an area of 50 square yards. During dry season, it was requested for 40 cubic meters per second of water to be discharged using the weir. If the discharge coefficient is 0.72 and the initial head of the weir was 1.20 m, how long will it take for the weir to discharge the demand as stated in the problem? 66.25 s O 43.85 s O 36.15 s 28.64 s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer the following with (True) or (False): 1- The head loss in box culverts varied linearly with the Manning coefficient. 2- In the sliding gate design, the plate considered as a beam simply supported on tow wall. 3- The total head in open flow is equal to velocity head added to specific energy. 4- The head losses in the syphon decreased with increasing of bend angle. 5- In the floor design, Bligh method is most economic method.
2.Water flows through a rectangular channel with a width b = 2 m and a height (Pw) = 1 m, the flow rate ranges from Qmin = 0.02 m^3/s and Qmax = 0.60 m^3/s. This flow rate is measured using Rectangular sharp-crested weir Triangular sharp-crested with = 90^o Broad-crested weir Plot onto the graph Q = Q(H) for each type of weir and give your analysis which type of weir is most appropriate to apply
Figure shows a horizontal flow of water through asluice gate, a hydraulic jump, and over a 6-ft sharp-crestedweir. Channel, gate, jump, and weir are all 8 ft wide unfinishedconcrete. Determine (a) the flow rate, (b) the normaldepth, (c) y2, (d ) y3, and (e) y4.
EXERCISE 3: Water flows at a rate of q=3.13 m/s.m in a rectangular channel shown in the figure on the right. Ja0.00023 no0.015 • Determine the uniform flow depths and the types of flow in Ja 0.00762 Pe-0.015 different parts of the channel. Draw the water surface profile in the transition zone,
Compute the location of the first gutter inlet from the crest, considering the following information: Maximum allowable flow = 0.35 m?/s Composite runoff coefficient = 0.40 Intensity of rainfall = 125 mm/h Width of drainage area = 75 m 333.3 m 275.4 m 236.2 m 416.7 m
QUESTION 4 Water flows in a rectangular channel at a depth of y₁ = 0.2 m and a flow rate of 7.5 m³/s. A hydraulic jump is generated and the width of the channel is 4 m. Chezy's roughness constant for the channel is 56 SI units. Determine: 4.1 the depth downstream 4.2 the Froude number downstream 4.3 the head loss in the jump 4.4 the bed slope
v² L 1) Show that the expression for head loss in a half full pipe is stilh, = f 2g D Why is it the same as for a full pipe? Prove to yourself that the bed shear stress in a rectangular channel is to=pgRhSo (see slide 157). What is the expression for a wide rectangular channel? 2) Find the necessary fall in elevation of the channel below if it required to carry a uniform flow of 25m/s over a distance of 10km. Assume a bed roughness of 3mm and use a Darcy friction factor. 1.5m 1.5m 4m 1.5m (Ans: (f-0.018), (C=66m²/s), 14.4m)
It was determined that for a length of 1.6 km of 90 cm diameter pipe made of wood staves the head loss is 5 m. Find the flow rate in m^3/s if f=0.016. a.1.54 b.1.72 c.1.18 d.1.36
1. Determine the depth (yo), bearing area (A), and wet circumference (P) of a trapezoidal shaped channel with the following known data mi = 2,5 m2 = 3,5 b = 5,5 m 1. mi Q = 24,5 m³/s m2 n= 0,014 So = 0,0003 %3D
It was determined that for a length of 1.6 km of 90 cm diameter pipe made of wood staves the head loss is 5 m. Find the flow rate in m^3/s if f=0.016. answers: a.1.54 b.1.36 c.1.72 d.1.18
The tank shown drains through a triangular weir whose flowrate is described by the equation given. Determine the time it will take for the tank to drain from completely full (h = 5 ft) to 5.25 feet deep (h = 0.25 ft) assuming there is no flow into the tank. Volumetric Flowrate h=5 ft + 5 ft 3 ft³ S = 2.48 h².5 (for h in feet) 10 ft -20 ft- -20 ft-
Water flows in a rectangular channel with a width of 2.5 m. The kinetic energy correction coefficient (i.e. velocity coefficient) is estimated as a = 1.2. If the flow rate is 5 m³/s and the flow depth is 1.5 m: (a) determine the specific energy of the flow. (b) Calculate the alternate depth considering α = 1.0.