Water is circulated from a large reservoir, through a filter, and back to the tank as shown. The pipehas a diameter, surface roughness, and length as specified below. (1hp = 550 ft-lb/s)1022=1KL elbow1.5K₁ filtermsib Filter10.0 - Gariw aqcopoK₁ 1.0exitKL valve = 6.0= 12.0KL ent = 0.8200 ft. of 0.1-ft-diameterpipe with &/D = 0.01Pumpa) Determine the horsepower required of the pump to produce a flow rate of 0.06 ft³/s.b) Determine the horsepower required of the pump to produce the same flow rate of 0.06 ft³/sbut with a pipe having the diameter.

The flow rate of the pipe is diameter of the pipe length of the pipe

KL elbow = 1.5 maib Filter exit KL valve = 6.0 KL filter = 12.0 KL ent = 0.8 200 ft. of 0.1-ft-diameter pipe with &/D = 0.01 Pump e the horsepower required of the pump to produce a flow rate of 0.06 E e the horsepower required of the numn to produce the

KL elbow = 1.5 maib Filter exit KL valve = 6.0 KL filter = 12.0 KL ent = 0.8 200 ft. of 0.1-ft-diameter pipe with &/D = 0.01 Pump e the horsepower required of the pump to produce a flow rate of 0.06 E e the horsepower required of the numn to produce the

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need the answer as soon as possible
Dimensions of a hydraulic cylinder are Dsore=178 mm, Dpiston Rod=50 mm. For a 1,6 m/min extracting speed; Determine the supply flow rate (It/min) Q= ? It/min
I juest need help with part b. As you can see 22.9 is incorrect. I will rate your answer, thanks!
Specifications: The total length of pipe in the three inch branch is 10 ft, and the length of pipe in the one inch branch is 8 ft. Brine (sg=1.04, m=10-3Pa*s) flows at 250gpm through the entrance at point A. Assume fully turbulent flow in both branches (f=ft). Pipes are standard Schedule 40 steel pipes. Assume the globe valve is partially shut so its equivalent L/D is 1000. For Part 1 of this project, you are tasked with determining the following: The flow rate in both branches The pressure drop in both branches The overall resistance coefficient
1
The air is measured at 20 deg. C and 533mm Hg. The duct diameter is 622 mm while the discharge diameter is 385mm The fan draws 2 m^3/s air and the static pressure measured is 8 cm water Determine the power output in kW ndmal places
I just need help with part b thanks. Will rate immediately.
As shown in the figure, the water flows from the ground floor of a three-storey house to the second floor through pipes of 20 mm diameter (average roughness of the pipe material = 0.0015 mm) at a volumetric flow rate of 0.75 L / s. Water is discharged from the system to atmospheric pressure through a tap with a 12 mm diameter outlet. There are 4 winged elbows, one ball valve and one faucet throughout the installation. Calculate the effective pressure at point 1. (psu=998 kg/m3, usu=1.12x10-3 Pa s, g=9.81 m/s2)
Solve Correctly urgent.
Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft3/s. a. H = 51 + 25.98(Q^2) b. H = 54 + 24.98(Q^2) c. H = 54 + 25.98(Q^2)
For the duct system, plot required fan head Hrequired (mm of water column) as a function of volume flow rate V. (Lpm). On the same plot, compare available fan head Havailable versus V. , and mark the operating point. Discuss.
Problem 01 Find the least number of 150 mm diameter pipes required to transmit 170 kW to a machine 3.2 km from the power station, if the efficiency of transmission is to be 90 per cent and f= 0.0075. The feed pressure is 4800 kN/m². Collutate of Pipes required efficiency= Problem 02 A turbine of efficiency 78% is 750 m lower than the supply water source. The pipe supplying the turbine with water is 200 mm in diameter and 4,5 km long. Take f=0,008 and determine the maximum power output that can be expected from the turbine. Problem 03 A pipeline is 1800 m long and 375 mm in diameter, and supply head at inlet is 240 m. A nozzle with an effective diameter of 50 mm is fitted at the discharge end and has a coefficient of velocity of 0,972. If for the pipe is 0,005. (a) The velocity of the jet (b) The discharge (c) The power of the jet C1Reg