1. Determine the depth (yo), bearing area (A), and wet circumference (P) of a trapezoidalshaped channel with the following known datami = 2,5m2 = 3,5b = 5,5 m1.miQ = 24,5 m³/sm2n= 0,014So = 0,0003%3D

Answered: Image /qna-images/answer/e4887911-7dc5-423f-84ad-1295e78ef435.jpg

Answered: 1. Determine the depth (yo), bearing…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Uniform water flow in a wide brick channel of slope 0.02°moves over a 10-cm bump as in Fig.. A slightdepression in the water surface results. If the minimumwater depth over the bump is 50 cm, compute (a) thevelocity over the bump and (b) the flow rate per meterof width.
Water flows uniformly in a rectangular channel with finished-concrete surfaces. The channel width is 3 m, the flow depth is 1.2 m, and the bottom slope is 0.002. Determine if the channel should be classified as mild, critical, or steep for this flow.
7. A long triangular open channel with two different side slopes, these are: 2:1 and 3:1 (H: V). The Manning coefficient is 0.014. The longitudinal bed slope =0.004, this channel is converted to the best economic section by using the same amount of material at depth 1.5m in the old section. The old and new flow discharges in m3/s (respectively) are: 9.9 & 57.5 29.8 & 67.3 20.5 & 14.5 19.9 & 37.3 None
In flowing from section (1) to section (2) along a rectangular open channel, the water depth decreases by a factor of three and the Froude number changes from a subcritical value of 0.7 to a supercritical value of 3.4. Determine the channel width at (2) if it is 8 ft. wide at section (1). Assume stead-state flow.
Water flows under the partially opened sluice gate, which is in a rectangular channel. Suppose that yA = 8 m and YB = 1.5 m. (Figure 1) Figure ▼ УА Part A A B 1 of 1 C Determine the Froude number at B Express your answer to three significant figures. T
Fluid Mechanics: Open Channel Flow
1. An actual discharge from a reservoir takes place over a rectangular weir where the flow characteristic is Q= 1.77 BH 3/2 m³/s (a) Find the length of weir (b) The ratio of actual discharge to theoretical discharge * Required to discharge 9 m³/s, if head must not exceed 0.6m

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

1. Determine the depth (yo), bearing area (A), and wet circumference (P) of a trapezoidal shaped channel with the following known data mi = 2,5 m2 = 3,5 b = 5,5 m Q = 24,5 m³/s mi m2 n = 0,014 So = 0,0003