A rectangular cantilever beam is 5 m in length and has b= The beam will be designed to carry a service 310 mm and d = 460mm. %3D %3D dead load of 230 kN - m and service concentrated live load of 38 kN at the free end. Concrete cover will be 70 mm from the centroid of the steel reinforcement. Determine the required steel area for f'c = 30 MPa and fy = 415 MPa. Draw the cross %3D section of the reinforced beam and show the details.

A rectangular cantilever beam is 5 m in length and has b= The beam will be designed to carry a service 310 mm and d = 460mm. %3D %3D dead load of 230 kN - m and service concentrated live load of 38 kN at the free end. Concrete cover will be 70 mm from the centroid of the steel reinforcement. Determine the required steel area for f'c = 30 MPa and fy = 415 MPa. Draw the cross %3D section of the reinforced beam and show the details.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need a solution quickly, Use ACI Code
Subject reinforced concrete design please solve part C and D
When we design doubly reinforced beams, what is the maximum possible value for Ku to get minimum area of compressive steel area? Select one: a. 0.36 b. 0.4 OC. 0.545 Od. 0.6 e. 0.8 A rectangular beam section has d = 450 mm, dsc = 45 mm and Concrete grade 40 MPa. When neutral axis depth is at its limiting depth, Ast = 3600 mm^2 and Asc = 620 mm^2 were provided to satisfy the design requirement. What is the design Moment capacity (M*) of the section? Select one: a. 692.6 kNm Ob. 584.0 kNm Oc. 466.6 kNm Od. 705.1 kNm Oe. Can not estimate without the value of 'b'
Given a rectangular section of b = 300mm, h = 400mm, a, = a', = 40mm; the concrete is of grade C30, the steel is HRB400. Find the reinforcement (A, and A') required for a load of M = 218kNm and an axial compression N= 396KN. %3D
A rectangular R.C beam of detail shown in Fig. subjected to bending moment of (150 kN.m), n=9, f'c = 28 Mpa, fy = 413Mpa, use the working stresses method (Cracked State) to find: 1- Maximum compression stresses in concrete. 2- Maximum tensile stresses in steel reinforcement. 4025mm 250 mm 500mm 70 mm
Beam section is b = 300mm, h = 450 mm. %3D Steel cover is 75 mm. Compressive strength of concrete fc' = 20.7 MPa, steel strength fy = 415 MPa. The beam is simply supported on a span of 5m and carries the following loads: dead load = 13 KN/m, live load = 10 KN/m. Find the required %3D number of 20mm Ø bars for the given cross section both in balance and ultimate condition.
A beam has a width of 280 mm and 490 mm overall depth. Concrete cover is 65 mm from the centroid of bars. Concrete compressive fc' = 24 MPa. Steel yield strength are fy=415 MPa and fy = 275 MPa for ties. Determine the shear strength provided by concrete using simplified method a) If the beam is subjected to shear and flexure only, and b) If the beam is subjected to axial compressive force of 124kN.
Design a reinforcement of a doubly reinforced beam if the beam has a size of 425 mm x 600 mm. Use fc = 21MPa , fy = 414MPa
need fast and comp, pls
A rectangular reinforced concrete beam exposed to earth has a total depth of 600 mm and a width o 350 mm. It is reinforced with 3-22 mm diameter bar (fy' = 315 MPa) in compression and 5 - 25 mm diameter bar in tension (fy= 345 MPа). fc' 3D 28 MPа a. determine the effective depth of the beam b. determine the depth of compression block C. check if steel yields for both tension and compression reinforcement d. determine the ultimate capacity of the beam %3D
*Subject: Reinforced prestressed concrete - Civil Engineering *Please refer for my attached formula or guidelines solve this problem A one-way both ends continuous slab is to support the moments tabulated. Consider L=5m, Fc’=21MPa and fy = 415 MPA. Dead load Moments: +42kN.m at midspan ; -67 kN.m at support Live load Moment: +40kN.m at midspan, -44kN.m at support. Determine the minimum thickness of the slab.
A concrete sectionwith b = 20 in. and d = 27 in. is required to develop a bending moment strength of Mr = 1000 kip-ft. Use of compressivereinforcement is desired. Find the required reinforcement. Use f ′c = 4 ksi and fy = 60 ksi.