50 mm wide, 500 mm deep is reinforced at the bottom with 4-2e-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar e concrete strength f'c = 27 MPa and steel yield strength fy = 345 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the ma: ve bending with the given material strengths and the tensile strain is limited to 0.004 upon crushing of concrete. Write the answer in

50 mm wide, 500 mm deep is reinforced at the bottom with 4-2e-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar e concrete strength f'c = 27 MPa and steel yield strength fy = 345 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the ma: ve bending with the given material strengths and the tensile strain is limited to 0.004 upon crushing of concrete. Write the answer in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A group of concrete cubes mixed with different water ratios .. The group with water ratio W / c = 0.3The maximum load was testedFailure causes every cube in the group Required:1- Finding the stress rate for each group in unit N / mm2 with discussing the results and the effect of the water w / c ratio on the compressive strength of the group.
NO 1 Please solve and answer correctly, give the complete solutions.
For the bean shown below, the concrete strength is 5000 psi and the yield strength is 60,000 psi. For the midspan section shown, check if steel yields and compute ØM, and compare it with M. WD = 1.2 kips/ft plus weight of beam WL = 1.5 kips/ft %3D 20.5 in 23 in 3 no. 9 bars 18 ft 11 in.
What is the value of the Whitney stress block parameter, β1β1, for 6000 psi concrete?
A half-block concrete masonry unit is subjected to compression until failure.The outside dimensions of the specimen are 190 mm X 190 mm X 190 mm.The cross section is a hollow square with a wall thickness of 38 mm. The loadis applied perpendicular to the hollow cross section and the maximum loadis 296 kN.a. Determine the gross area compressive strength.b. Determine the net area compressive strength.
Q-A pre-tensioned concrete member of section 200 mm x 250 mm contains tendons of area 500 mm² at centre of gravity of the section. The prestress in the tendons is 1000 N/mm². Assuming modular ratio as 10, find the stress (N/mm2) in concrete.
A pre tensioned concrete member has a rectangular section 250 mm x 400 mm. It is concentrically prestressed with 20- 6 mm diameter high tensile wire, which is anchored to the bulkheads at a unit stress of 1035 MPa. Compute the stresses in concrete immediately after prestressing. The beam is supported throughout its length. Draw stress diagrams.
A simply supported beam 6.5m long, 350mmx500mm, prestressed with a straight tendon located 150mm below the neutral axis with effective prestressing force, Pe, of 300kN. Total load carried by the beam is 20kN/m. A. Determine the area of the concrete, mm2.B. Determine the section modulus of the concrete in x10^3 mm^3C. Determine the compressive stress caused by the tendon alone if Pe is at the centroid, MPa
Find the minimum theoretical width and height of a rectangular concrete section that will make the beam failure sufficiently ductile. Given: Two layers of 2-Ø25 mm bottom reinforcements fy=414 MPa f'c=35 MPa stirrup diameter=minimum required clear cover=minimum value for beam vertical clear spacing bet. Iayers=minimum value for beam height-to-width ratio=2.0 Note: Ductile failure occurs in beams when the extreme reinforcement layer is strained to 0.004 or greater.
Determine the cracking moment (KN/M) and the compressive stress felt by concrete (MPa). Show your step by step answer with solution
A rectangular beam with width of 233 mm and overall height of 431 mm is prestressed by using a bonded (stress relieved) tendons with a specified tensile strength of prestressing tendons fpu %3D 1380 MPa. Strength of concrete is 33.1 MPa. The area of presstressed reinforcement in tension zone is 1,024 mm2 and its centroid is located 40 mm above the bottom end of the beam. The specific yield strength of prestressing tendons fpy = 1220 MPa. Compute for the ultimate moment capacity of the beam.
I need the answer quickly