2 A rectangular beam has b=320 mm and d=470 mm. The beam will be designed to carry a service dead load of 235 kN-m and service live load of 195 kNm. Compression reinforcement if necessary will have its centroid 70 mm from extreme concrete fiber. Determine the required steel area, Use fe=30 Mpa and 1, = 415 Mpa. Ans: A's= As =

Q: Apart from the ambient air temperatures, list two factors that would be considered to select the…

A: Performance grade (PG) bitumen cement is basically used for the enhancement of the design life of…

Q: What is the effect of Dust loading on the efficiency of  a cyclone seperator?

A: Solution: The geometry of the separator basically imparts the efficiency of the units. A cyclone…

Q: In an aperment complex, there are 5 windows in each apartment, and 9 apartments in each floor. How…

A: In an apartment complex, there are 5 windows in each apartment, and 9 apartments in each floor.

Q: Reasons and defects for floors men

A: Solution: Proper floor care is needed for every aspects of business like for carpet, wood or Tile…

Q: What is the minimum dimension of septic tank in residential building?

A:

Q: Describe about the bailers and for what it is used.

A: Bailment happens when someone voluntarily transfers property to another person for a specific…

Q: What is internal drainage and what can it result in?

A: Drainage is indeed the natural or artificially elimination of surplus water from the surface of the…

Q: Observe several construction sites and ascertain details oftheir safety program. If possible, attend…

A: As a construction site trainee engineer, I visited more than 5 construction sites in the past 1…

Q: What are the fire rating classes used to rate asphalt roofing materials?

A: The Fire rating classes is specified by the Underwriters Laboratory. The fire rating is one of the…

Q: Given a simple floor plan, compute for: a. Concrete materials b. Masonry materials

A: Given Data: The length of a longer wall is 10.00 m The length of a shorter wall is 8.00 m The height…

Q: What does the pacer test look for?

A: Answer -  Aerobic capacity, which is defined by endurance, performance, and fitness, is what the…

Q: air stripping column function

A: Air stripping columns are most widely used for the removal of volatile organic compounds (VOCs) from…

Q: Construct the PERT Met work for the data Shown below and determine the exPected finish date ,f…

A: First we will calculate the expected time of each activity

Q: All kinds of recognized hazard should be mentioned and prioritized by how often they occur, with URL…

A: It is asked to recognize all the kinds of hazard and prioritize by how often they occur with URL…

Q: penetration testing involves

A: Penetrating test is a simple and economic test done in soil by penetrating or boring a hole in soil…

Q: How to design the bar screening and grit removal of a wastewater treatment plant? What calculations…

A: We have to determine the various aspects of grit chamber or bar screening and have to design the…

Q: What Item No. is "Aggregate Surface Course" in the DPWH Standard Specifications for Highways,…

A: Department of public works and Highways deals construction  of highways, bridges and airports under…

Q: fé = 4000psi, Grade 60, NWC Psteel = = = = Pb Please calculate As = ?

A: Answer  We are given b = 12 inch d = 18 inch h = 21 inch steel cover = 3 inch f'c = 4000 psi Grade…

Q: Explain the Least Count of Dumpy ?

A: Dumpy level : A dumpy level also known as Builder's level is an optical instrument used to establish…

Q: What are possible Pro-active replacement of wear and tear parts, and keeping of thorough records of…

A: Proactive replacement of wear and tear parts is essential to prevent unexpected breakdowns and…

Q: Explain the Specifications for Modified Proctor Test (Based on ASTM Designation 1557) ?

A: Modified Proctor Test : Modified Proctor Test is used to determine the compaction of different types…

Q: Define Vacuum Consolidation.

A: Vacuum consolidation is defined as the technique which is used for improving  the property of soft…

Q: FAR/AMT Part 65 According to FAR Part 65, what are the privileges and limitations of the Airframe…

A: Airframe rating:It is issued to repair stations for the maintenance and the alterations on…

Q: What are the differences between on-site and off-site storage?

A: The difference between on-site and off-site storage is required to be considered according to the…

Q: What are the objectives of an Automatic blackboard/whiteboard cleaner system?

A: Automatic blackboard/whiteboard cleaner system is designed to save a lot of time and unnecessary…

Q: How to design the bar screening and grit removal of a wastewater treatment plant? What calculations…

A:

Q: Describe the TRD method.

A: TRD stands for Trench Re-mixing and Deep wall. It is a one-phase process for excavation and in situ…

Q: Define the term block failure.

A: Block shear failure generally occurs in Steelmember connected to a gusset plate.

Q: What are Wet-Impingement Scrubbers?

A: Wet-Impingement Scrubbers:

Q: Determine the number of studs 16" o.c. needed for each of the following wall segments of buildings:…

A: Studs is the vertical member used in the construction of wall framing,  Formula to calculate the…

Q: Explain in details about the bridge maintenance system and also about the inspection instrument used…

A: Maintenance of Bridges : he maintenance of bridges means the up-keeping of the bridge components in…

Q: 8. Define psychrometry.

A: To define:The term psychrometry.

Q: first step for sidewalk repair work?

A: Concrete is one of the Most important Material used in Construction Industry. Generally considered…

Q: Select a particular material item (e.g., concrete) and follow its material handling process from the…

A: Special equipment for Earthwork as; Excavators Backhoe Dragline Excavator Bulldozers Graders Wheel…

Q: 5. Verify the identity: 1 sec x V secx + tanx tan x secx + tanx

A:

Q: What is consolidation test?

A: - Consolidation test is used to calculate the rate of consolidation and and magnitude of soil…

Q: QC inspections and tests are performed to check quality of work and are carried out by owner's…

A: Solution; QC is generally known as a Quality check.

Q: In which industries are spray chamber scrubbers used?

A: Spray chambers are commonly known as spray towers which are used as an air pollution control. These…

Q: Describe the Effects of Drainage.

A: The drainage can be defined as it is an artificial or a natural process of discharging surface and…

Q: What does the pacer test look for?

A: Answer - The PACER fitness exam is an excellent method for encouraging kids to love exercise. It…

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.