A rectangular beam has b = 310 mm and d = 460 mm. The beam will be designed to carry a service dead load of 230 KN-m and service live load of 190 KN-m. Compression reinforcement, if necessary, will have its centroid 70 mm from extreme concrete fiber. Determine the required steel area (tension and compression). Use f'c = 30 MPa and fy = 415 MPa.

A rectangular beam has b = 310 mm and d = 460 mm. The beam will be designed to carry a service dead load of 230 KN-m and service live load of 190 KN-m. Compression reinforcement, if necessary, will have its centroid 70 mm from extreme concrete fiber. Determine the required steel area (tension and compression). Use f'c = 30 MPa and fy = 415 MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Use USD method.
A rectangular concrete beam has a width of 300mm and an effective depth of 550mm. The cantilever beam is loaded as shown. Assume f = 21 MPa and fy = 312 MPa. Compression reinforcement if necessary shall be placed at a depth 80mm from the outermost compression concrete. Determine the required number of 25mm tension bars. Draw the details of the rectangular beam. 20 kN/m 3 m 2 m 2 m 40 kN
A beam cast monolithically has the following properties: bf=1200mm, t or hf = 110mm, bw=380mm and h=800mm. It is reinforced with 10D32mm grade 420MPa bars. Concrete strength is assumed to be 27.5MPa and the centroid of tension reinforcement is located 665mm from the outermost compression fiber. A. Determine maximum nominal moment to ensure tension controlled, kN-m. B. Calculate the balanced steel area, mm2. C. Calculate the balanced moment in kN-m.
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 27 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the maximum steel ratio if the beam is singly reinforced in positive bending with the given material strengths and the tensile strain is limited to 0.004 upon crushing of concrete. Write the answer in 5 decimal places only.
RCC.
rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 420 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the maximum steel area for a tension controlled singly reinforced condition in positive bending
Find the maximum allowable value of P for the column. The cross-sectional areas and working stresses (ow) are shown in the figure. |2P Steel: A = 500 mm2 Ow = 120 MPa P Timber: 4P A = 2000 mm? Ow = 12 MPa Concrete: A = 8000 mm? O = 16 MPa
A reinforced concrete beam that is 375 mm wide and 500mm deep must resist a service live load moment of 250 kN-m and a service dead load moment of 150 kN-m. Use f'c-21 MPa and fy=415 MPa. The effective concrete cover is 65mm (to the centroid of reinforcements). 1. Determine the area of compression steel reinforcement (If required. Answer O if not) in mm² 2. Determine the minimum number of 25 mm diameter bars to be provided to satisfy the demand ultimate moment 3. Determine the maximum number of 25 mm diameter bars to be provided to have a tension controlled section Answer 1: 2403.21 correct answer: Answer 2: 9.00 Answer 3: 8.00
Please answer as soon as possible
A rectangular reinforced concrete beam has a length of 14 m is simply supported atboth ends. The width of beam is 350mm and the overall depth is 550 mm. Determine the area of the steel reinforcements if the beam is to carry a DL = 15kN/m and LL =18kN/m. The concrete strength fc = 25 and steel yield fy = 400 ��. Use 60 mm concretecover.